Tuesday, June 25, 2019

Replacing the Mast Steaming Light and Deck Light

Replacing the Mast Steaming Light & Deck Light

After a 10 hour trip arriving at midnight, I noticed that the steaming light was really dim, and from previous trips up the mast, I knew it was a bodged job - The Deck light part of the combo lamp must have failed and someone choose to replace the deck light lamp with a new fitting - ie. now there is a Steaming light and a pair of wires going to a separate deck light (Halogen Lamp). So, time to replace both as it's impossible to fix either lamp.

Step 1 was to remove the old lamps
If you zoom in on this pic, you'll see the amount of silicone sealant that had been used to try and waterproof the fitting.

The wires from the deck light (lower) and the combo fitting (upper) are nicely joined and heat shrink tubed, but again, a huge glob of silicone was used to try and water proof the connection.


The lens of the steaming light is cracked from years of UV exposure - these lamps don't last forever!





The two wires coming out of the bottom of the combo unit are actually soldered inside the fitting and then gooped with more silicone. Click on the pic and zoom in.

Yes, that's my Sailrite machine in the background.















Special Thanks to Steffi Shiffer & Peder Sahlin for coming down to the boat dock to act as Safety while I went up the mast.

I spent about an hour up the mast sat in my bosuns sling (not really a chair) and that's not comfortable, the straps grab right where a guy doesn't want to be grabbed. 
During that hour I was able to drill out the rivets that held both fittings in place and scrape away about 90% of the silicone (another tube) off of the mast. 
There are a total of 12 holes in the mast from these fittings and previous fittings, they will need to be filled and the remainder of the silicone scrapped off and cleaned up - I'm going to get a new Bosun's Chair that doesn't try to cut of important blood supply.









This is the new combo fitting.

It has 9 LEDs in the steaming lamp and 12 in the deck lamp.

The mounting only has 2 screw holes and they look to be the same dimension and location as the removed fitting.

I'll mount the fitting with Stainless Screws using anti corrosion protectant between the surfaces.

I'll also use a SS washer to spread the load over the tab of the plastic wings of the fitting.

A trick I figured out a long time ago, is to grind down the sharp point of the screws so that they cannot catch the running rigging lines inside the mast - I'll use my cordless Dremel to cut off the screws and then grind down the edges of the cut so that they are nice and smooth.

West Marine has a July 4th sale on their Bosun's chairs - so we'll visit there before the weekend. 
Then it's back up the mast to tidy up the mounting area, cleaning off the silicone and filling the holes (JB Weld) I'll also apply a bead of silicone in an inverted U above the grommet where the electrical wires come out of the mast. I'll also apply a bead of silicone inside the edges of the new fitting wings just to encourage water to stay away from behind the fitting. Plan is to not be able to see any silicone when the new fitting is installed.

More later - meanwhile, we'll see you on the water.




Saturday, June 22, 2019

Upgrading the Cabin Lighting

Upgrading Eximius' Cabin Lighting

We have a variety of lights in the Cabin, the result of units being replaced by a smorgasbord of fittings. During our New Year's Eve Cruise, the Galley Lamp failed and has to be replaced.
I prefer that they are common fittings so that replacement is easy.


  • Galley: 12" LED Strip  - 1 white, 1 red (Both New - replacing broken florescent) 
  • Table Reading light: LED lamp White - Blue night lite option. (New - replacing weak LED)
  • Nav Table: Red LED lamp (original)
  • Port Settee: 12" LED Strip - 1 white, 1 red (Both New - replacing original)
  • Stbd Settee: 12" LED Strip - 1 white, 1 red (Both New - replacing original)
  • Port Side: 8' LED Strip White - Installed over a year ago.
  • Deck nite lites: Low Power LED lamps (Installed about a year ago, white - to be painted with thin, Red, Nail Polish)
Later, when upgrading the V-Berth & Aft Cabins, we'll use the same types of fittings.

Here's what the new fittings look like.


The 12" LED Strips are Self Adhesive (3M VHB tape) from Amazon. they come in packs of 4 all the same color.

In each lighting set, will be 1 strip of white, 1 strip of red and 1 dual switch. I went with the simplicity of dual switches rather than On-Off-On switches.

The 'Sets' will be used at the Galley, V-Berth and Aft Berth and the Bathroom










These switches are small enough to fit on the Wooden battens in the Cabin, Aft Cabin and V-Berth.

One switch will operate the White LED Strips, the other will operate the Red LED Strips.

See the wiring diagram below.

These Reading lights do not require switches, they have a built in Touch Sensitive feature.

This does mean that they consume power when turned off, not much, but any 'always on' lamps will eventually drain an uncharged battery.

Our normal practice is to turn off all systems at the Electrical Control Panel, including the Cabin Lighting circuit, so this will not be a problem.

The 'Touch Sensor' is the thin ring near the top of the lamp (where the finger is pointing)
1st touch turns the Blue rings on, 
2nd touch turns the Reading lamp on Blue rings off
3rd touch turns Reading lamp off.

The Reading Lights will be used in the main cabin(2) and the Aft Cabin, the V-Berth is not really a reading area.

All of the new lamps will utilize the existing wiring, but the switches to lamp wiring will be new.

Amazon Links

Wiring Diagrams


Pics of Completed Installations

Red Light On
White Light On



Tuesday, June 11, 2019

Stormy Regatta

Bad weather story

On Saturday, we took part in the Hillsboro Inlet to West Palm Beach Sailing Club regatta (Lake Worth Florida). We left our dock Friday Morning and headed up the Intra Coastal Waterway to stay the night along side our friend, Peder, Catalina 36, 'Dalecarlia' in Pompano Beach. The trip was uneventful and we arrived at Peder's place while he was in the process of cleaning his boat's bottom in prep for the regatta. There were 22 boats registered to participate. We were in the Gunk Hole class as we really don't race, but the event was a great excuse to sail up to Lake Worth.

Saturday Morning, Peder appeared with an offer for morning coffee, but I had just poured my 2nd cup of coffee and was going through the process of getting the boat ready to sail. His dock is only 3 miles from the Ocean and just 3 bridges. I put my coffee mug down by the Port side dorade while I released the Main sail Halyard - promptly forgot about the coffee.

By 08:15 we were ready to head out, Peder & his crew were ready too. So we headed out, slow, it was near low tide and he had warned me about an obstruction on the South side of the canal entrance from the ICW. Peder should have warned me to stay near the middle of the entrance, as there was some shoaling on the Northern corner of the entrance. Yep, we went aground - soft sand - we know how that feels after previous soft groundings. We were able to slowly move off the shoal and catch up to Peder who had passed us on our Stbd side. At the Hillsboro Inlet bridge, there were at least half a dozen club boats waiting for the bridge to open, then we all passed out of the inlet, some boats peeling off to raise their sails before going out of the inlet.

We totally screwed up the start! Our class was 2nd to sequence through the start gate, each class being 5 minutes later. We crossed the start line just before the last class started - 20 minutes after our start - as I said before, we're not racers and don't normally stick to a schedule. We're Cruisers!

There was very little wind, 'The Rabbit' had his Spinnaker up, but it barely filled as he headed off shore to catch the Gulf stream. We opted to stay inshore where we had 2 knots of current carrying us to the North. Almost all of the other boats headed out to the stream where the current would be somewhere higher, but at the cost of having to head both a couple of miles East to get to the stream and then a couple of miles back to get to the finish line. As we would move a lot slower, the extra speed of being in the Gulf Stream didn't seem to valuable to us.

So we quietly, slowly, almost monotonously, crawled up the coast and our ETA at the finish line was about 16:30 according to our GPS Navigator. Of course, it started to rain, that fine drizzle that soaks everything but was barely reason for donning our Foul Weather gear. As always, we had our life jackets on and the Jack Lines were set just in case we needed to go forwards to adjust anything.

The 'Catalina Motor Yacht', one of those dinner cruise types boats, crept up on our stern, we could see them on our AIS before we could see the boat. I called the skipper to ask if they could see us on their AIS, this would be our first confirmation that our new AIS Transceiver was transmitting. They called us back and confirmed they could see us, they even replied pronouncing our boat name correctly, it's displayed on AIS receivers, along with our Speed, Course over ground and some other info about our boat.

'Catalina' motored off towards Lake Worth and by that time we could see Dalecarlia and 'Gratitude' a Hunter 27' both of which had gone out to the Gulf Stream but were now heading back inshore.

The wind had picked up from an earlier 5 knots at 140º off our Stbd Bow to 12 knots. As per our sailing plans, we started to reef. Two reefs in our Jib and One in the Main. We were now doing 7 knots GPS, not shabby!

I was thinking through the race results: Our rating was 186 seconds per mile, Peder's was 196 spm, and Gratitude's was 228 spm.  With a race distance of about 30 miles, Gratitude could finish 21 minutes after us and still beat us. Peder could  finish 5 minutes after us and still beat us. Both were closer than that, Peder not so sure, but pretty close.

All of a sudden, the wind instrument went crazy, showing the wind changed direction by nearly 90 degrees and ratched up to 20 knots. I looked over to Dalecarlia and saw him heeling hard and spinning around to starboard and thought 'What the heck is Peder doing?' when WHOOSH! we did the same, the wind spiked to above 39 knots, at least that's the biggest number I saw when I had a chance to look at the Instrument! The boat heeled hard over to Port and dipped the rail well below the water line, wave constantly bursting over the side and occasionally over the cockpit combing.

Peggy was hanging on for dear life! Both arms wrapped around the cabin top winches and feet firmly reaching for the port side seat, trying to jamb herself into position. All the while I was trying to see the instruments through fogged up glasses and holding the wheel to stop us bearing off the wind which would have put us beam to the wind, that would have been even worse.

We've been in squalls before, they typically have lasted maybe 10 minutes max, so I told Peggy to hang on, it's going to calm down in 5 minutes or so. It didn't! More than 20 minutes later, we agreed that we should try to pull in the remaining Jib and put the 2nd reef in the Main sail. I didn't think we could lower the main because it was under such stress with the high winds.

I helped Peggy bring in the jib, step by step, we worked together, Peggy jacking the furling line and me taking the line slack up on a cleat. Then Peggy easing the jib a bit more and then more struggles with the furling line. Peggy was pretty worn out by that time, so we took a breather till we tackled putting the 2nd reef in the Main. All the while, the Port side is dipping in and out of the water, still getting occasional floods into the cockpit, but the drains emptied it pretty quick. We were both soaked through even wearing our rain jackets. The wind dropped to below 25 knots, and we tackled the Main sail. Peggy dropped the main halyard about 5' and secure it. Then she passed the 2nd reef down haul line to me and I pulled the sail down to the 2nd reef position. Peggy secure that line in it's line clutch and we did the same for the 2nd reef out-haul line. It was not a perfect reef, but there was a lot less sail up than with just a single reef.

After about 30 minutes, the wind started to ease below 20 knots. I raised the head of the mainsail in order to clean up the reefing, it only needed to be raised by about 8 inches. That made the sail look a lot more orderly, and then the wind died, I mean it dropped so much we were only doing 1 - 1 1/2 knots downwind towards the finish line. Our ETA went from 16:30 to 17:45, time to drop out of the race, so we started the engine and called the race committee to announce we were dropping out.

With the engine running, we dropped the mainsail and headed to the finish line which was now about 7 miles away. I tided up the running rigging lines and we did our best to relax and ease back down from the high stress of the squall.  We heard other boats call in to drop out or announce they were ok. We called Dalecarlia and they were ok, minor damage - bimini split and mainsail jambed half way down. Gratitude was ok too.

We motored in over the finish line. The Palm Beach Sailing Club boat 'Paparazzi' stayed at the finish line until we passed it, we were the last boat in.

None of the Gunk Hole boats officially finished due to the storm, but we all got safely to the anchorage opposite the PBSC marina.  Dalecarlia was offered an overnight mooring ball and we agreed to tie up along side them. We kept clear until they had completed their mooring connection and then I prepped for going along side, getting fenders deployed and lines set.

After healing, probably as much as 50º to port, having water wash all along the side deck, in winds that, according to others, was over 50 knots, anything loose in the cabin was all over the floor including the seat cushions. So it was with amazement that, as I was setting the fenders on the Port side, I found my Coffee Mug, laying within inches of where I had left it before leaving Peder's dock 10 hours earlier!  Go Figure!

Once we were all secure and ready to go ashore for the After Race Party at the sailing club, we hailed the tender for a ride to the club. Ken, one of their sailing instructors, quickly arrived and took us to the club, I think we were the last to arrive.

We sat with a few of our club members and enjoyed the club's excellent dinner and the much needed Cold Beer!

When it came to the awards, the master of ceremonies announced that as none of the Gunk Hole class had finished, and that the club had made 3 really nice Trophies, they would have the 3 skippers tell the story of their experience of the storm and award the trophy according to the applause rating of the audience!





Enough Said!
Our First Racing Trophy
Even if we didn't finish!

See you on the water!




Tuesday, June 4, 2019

Broken Window Latch

Look what fell off the window?


 This is the Forward Beckson Portlight in the Aft Cabin.
The lower right latch fell off! The insert that attaches the latch to the screw (seen hanging down) broke in two.

Good news is that Beckson is still in business.





The broken latch.

Buddies on the C34 forum pointed out that they were still available from Beckson

Just $15 on line. purchased two of them, if one has broken, probability of other following after 30 years is pretty high.







Found them by searching for: Beckson PRK-W Latch Only

Easy fix.

See you on the water.