Thursday, August 26, 2021

Autopilot upgrade - installing the EV-100 Sensor


Installing the Raymarine EV-1 Sensor Core


This is the new EV-1 Sensor Core, part of the Raymarine EV-100 Autopilot kit we're using to replace our existing Raymarine Autopilot - if you have read the previous posts, you know, the old unit is suffering from Alzheimer's - It doesn't know where it's going and keeps on forgetting things.






This is the old Autopilot's Compass unit. It's mounted on the bulkhead with the door to the Aft Berth, the new unit will not fit there.

The new unit has to be at least 1m (3'3") from the engine, other electronics or magnetic interferances.

Also, the top of the sensor puck has an LED that should be visible and is only visible from the top of the sensor puck, so the new sensor has to be about 12" from a deckhead (ceiling) and that really limits it's location on Eximius. We have a couple of meters long SeaTalkng cable to facilitate positioning the sensor from the ACU. In response from Raymarine, the EV-1 has to be a minimum of 1m from the ACU.  We're working on that location issue.

Finally figured out the location for the EV-1 sensor.


That is on the bulkhead between the Galley and the Aft Berth Starboard side.

The Raymarine Spur Cable is connected to a SeaTalkng Backbone via a 400mm spur cable. The backbone cable connects to a T-piece has a terminator on one end and a backbone cable on the other.

The backbone cable is secured to the existing wiring loom above the soffit under the deckhead (behind the teak piece)

I spoke with Raymarine support this morning and a really helpful guy confirmed that I should not connect the NEMA2000 to the SeaTalkng network via a spur cable, but via a backbone connection cable.





This change eliminates the 5 way backbone connector and replaces it with a single T-piece connector.
The result is a more simplistic schematic but it adds about $150 to the project. I should be able to return the unused SeaTalkng to Device net Spur cable and I'll have to sell the additional equipment on Craig's list or E-Bay. 

On yesterday's visit to the boat, I did get the cable for the Rudder Position Sensor secured to existing looms all the way to the ACU and a few of the other cables setup for install. Definitely making progress. The new connectors will not arrive until Friday next week, but I have plenty to get done before then. It does look as though the install will not be done in time for Labor Day weekend, we'll see how it goes. I could get everything else done before the last few bits arrive, so maybe we could sail that weekend. 

See you on the water - really! That's the plan.

Sunday, August 15, 2021

Autopilot Upgrade - Mounting the p70s Control Head

 Mounting a Raymarine p70s Controller


The Autopilot Controller for the existing system is mounted on the Starboard side bulkhead adjacent to the Helm Wheel. To reach it we have to bend or sit down to operate the buttons, definitely not the best position for the controller.

This is the New 'p70s' Autopilot Controller. Size wise it is almost identical to the Garmin GMI 20 Instrument already mounted on the Helm Nav Shelf. So I'm making a similar mounting unit.

Sadly, the plumbing business has changed the design of their End Caps for their 3" PVC Pipe. Good news, is that the new end caps are even better. So the new mount is only two parts instead of three for the GMI 20 instrument mount.







The mount is made from 3/4" Starboard and is 6" along it's longest edge (lower left in this pic) and 5" Wide.

The back is made from a 3" PVC End Cap from lowes. $5.35

I drilled out the Starboard with a 3" hole cutter (the internal diameter of the End Cap) 

Secured the end cap to the starboard using 1" #4 philips flat head SS screws.

There's a hole in the lower side of the end cap for the connection to the SeaTalkng cable to the Backbone.





The lower edge of the Starboard is cut at an angle that matches that of the Garmin GMI 20 Instrument so they pretty well match now.

Getting the bezel off of the instrument is a little tricky when the instrument is mounted. I found using a very fine pin Pick it comes off pretty easy.







The finished product, total cost about $10 including screws, Starboard (purchased from Sailorman in Fort Lauderdale by the lb) and the End Cap.

It will be secured to the Helm Nav Shelf using a couple of screws from underneath the shelf into the bottom edge of the Starboard.

Very pleased with this part of the project.

Next part is to install this at the helm and run the cables through the cable glands near the bottom of the pedestal guard. Looks like we'll be doing that on Wednesday.





See you on the water ---- Soon! 

Update - Wednesday August 2021
Well that went well.
This morning I went down to the boat with a plan - reposition the instruments and mount the new p70s Autopilot Control head in it's new holder.


This is the Helm Nav Shelf before today's work.
The Garmin GMI-20 is on the starboard side of the shelf. The GPS mount is centered at the back of the shelf. The Garmin Echo instrument mount is on the port side of the Shelf.

That black line is a zip tie that we use to hold down notes that we keep at the helm like the bridge list for the ICW or the Dock map of the various marinas we visit.

Left side of that picture is forwards, Top is to Starboard and right is aft.








After the work, the GMI-20 is on the Port side and the Autopilot p70s is on the Starboard side.

Not shown in this picture, the Garmin Echo Depth instrument is now located to the Starboard side of the Pedestal guard.

The data and power cables are temporarily secured to the Pedestal guard but are not re-routed to their final position yet. That requires the opening of the cable gland at the foot of the Pedestal guard, pulling the wires up from the aft berth, repositioning them to the shortest side.

When completed the wires will be routed as follows:
Port Side Gland: GMI-20, GPS and Radar Cables
Stbd side Gland VHF remote, p70s, Echo Depth, Autopilot Wheel motor.

First step in that process is to clear out the Aft Berth (our Garage) so that we can get to the old Autopilot's ACU. Remove the old Fluxgate Compass, run new power cables etc. etc. Worth another post.

Again - See you on the Water.


Thursday, August 12, 2021

Installing the Raymarine Rudder Position Sensor

Installing the Raymarine Autopilot Rudder Sensor (RPS)

This starts off techy, but read it to the end.



As mentioned in the previous post, the plan is to mount the RPS on the underside of the Aft Locker Shelf Support Beam. 


The RPS arm must be parallel to the Steering Radial Drive Radius when the rudder is amidships. There is a small amount of adjustment of the sensor (it has 3 extended slots in it's mounting base)




Schematic of RPS
Connection to the Steering Radial Drive


The vertical alignment of the RPS and the Tiller Pin has to be within +/- 5º Max. I'll make several Starboard Mounting plates of different thicknesses and use those that are needed to get the alignment within tolerance. I have several thicknesses of Starboard, so this should be easy. 

Well that first layout didn't work. The vertical alignment of the Tiller Pin would move everything down too low on the Steering Radial Drive - there would be huge chunk of starboard on the underside in order to clear the ridges.

Second design: Duh, looks a lot simpler.
This pic shows the underside of the Steering Radial Drive, that hole with the cable poking through is the problem for the 1st design.

Duh - Just make a bracket that can be held in place using the Thru bolt (center of the 5 in the pic) 

Basically an L shaped bracket made from 2" x 1/4" Aluminium Bar and mount the Tiller pin near the end of that bracket. There's a flat surface behind the head of that center bolt, so the bracket should be solid enough. I'll add a few brazed shims to the bracket if needed to ensure it's soli





Schematic of Tiller Pin and Support Bracket

Down at the boat again this morning with a makeshift Tiller Pin Support Bracket, just to figure out the size of the RPS mounting plate. We'll also check the max Rudder Angle, it has to be less than 60º from Center to Port and Starboard. The pic above shows the dimensions


To make the Bracket, I purchased a 24" piece of 2" x 1/8" Aluminium Bar Stock from Lowes. Marked the bar about 6" from the end. With the bar held in an Oven Gloved hand, and a plumbers Butane heat gun in the other, I heated the bend mark for 5 minutes. Then set the hot bar between a couple of garden stepping stones and bent the bar to shape. After cutting the bar to size, drilled the end hole and the Tiller mounting pin holes. Aluminium nuts and bolts hold the Tiller Pin in place, Loctite to keep them there. 

I added the two SS screws and lock nuts to add stability to where the plate is attached to the casting on the bottom of the steering radial drive. Plan is to attach the bracket using the center rudder post bolt, then tighten up on the two stabilizing screws and lock them in place with the lock nuts.




In addition to the Tiller Pin Bracket, I need to make a shim on which to mount the RPS and then mount it under the Port Side Shelf support beam.
1/4" thick Support shim 
I made 2, the other is 3/8" thick


The Install process will be:
  • Remove the Thru Bolt which prevents the Steering Radial Drive from rotating on the Ruder Post.
  • Install the new Tiller Pin Bracket on the bolt and reinsert the Bolt and secure in place.
  • Mount the RPS on the new Shim.
  • Align the shim so that the Pin on the RPS and the Tiller Pin are aligned and the RPS arm, Tiller Pin mount form a Parallelogram.
  • Run the Connector wire from the RPS forwards over the Aft Water tank and then join the loom of wires that reach the APU.

With everything prepped, I just need to get down to the boat early enough to be the heat or late enough for it to have started cooling down. Currently, the daily noonday temp is typically in the high 90ºF :(

Anticipating that I should be able to complete the RPS install in just one more trip to the boat, I'll hold off publishing this post until then.   Tuesday August 10th 2021

Update:  Thursday August 12 2021
Well, after getting all of that prep done, we took a break on Tuesday to get our Vaccinations - not Covid, we did that back in January, no, on Tuesday we got our Shingles Vaccine - shot #1 no biggy. Well, no biggy till Wednesday morning. Couldn't sleep all night and woke up unable to lift my left arm. Ibuprofen did not dull the pain! Wow, it gave me a little insight to what people suffer when they lose control of a limb. So Wednesday was a write off, I was able to steer my electric lawn mower, but very tenderly. So I mowed the lawn single handed.

Thursday almost 100% back in action. Lifting my elbow as high as my shoulder was slightly painful, but I felt I could make progress on this project.

We were down the boat by 10am and quickly got to work. 

Step 1 was to remove the center bolt. This pic shows the two shelf support braces on either side of the Steering Radial Drive. Removing the bolt took some doing, over 1/2 Hour to get it out, glad I'm a skinny guy.  That small USB powered rechargeable battery fan helped me keep my cool.

The bolt was a really tight fit through the rudder post, it needed a little persuasion but there's no room to swing a cat, barely room to tap the bolt with a hammer (of course I had a nut on the end so that the thread was not damaged.)

With the bolt out I took a break. The plan was to divide the job into steps. Step 1 done, got the bolt out.

Step 2  fit the Tiller Pin Bracket.  Step 3 install the Rudder Position Sensor with it's mounting plate. Step 4 fit the connecting stud between the Tiller Pin and the RPS pin.



After sweating for another hour, the Tiller Pin bracket is installed. There was no need for the stabilizing bolts, it's secured really well just using the Center Bolt.

This photo was taken after the install was completed, it shows the Connecting stud already installed.












Peggy had a good idea! Use a clamp to hold the RPS unit mounting plate to the underside of the shelf support braces.

I didn't have a suitable clamp on board, but I did have a velcro strap, it worked like a charm. That probably saved the day, I just don't see how I could have held that mount in place and screwed the plate to the underside of the shelf support brace.

Thanks Peggy.





This shows the completed install. the RPS is screwed to that Green plastic plate which is then screwed onto the underside of the Shelf support brace.

The biggest issue is getting the alignment correct and I'm not sure how accurate it is. This area is really difficult to work in.

The RPS has 3 slots around its circumference, that allows for some adjustments. The Connecting stud also has about 1/2" adjustment due to the two nuts on the connecting stud. 


Now that it's completed, I took this set of images.
But just to give it some context, this job involved quite a bit of Boat Yoga.

Getting into the aft locker / lazarette, takes some doing, but getting down into position in order to be able to reach the underside of the Steering Radial Drive requires a bit more flexibility.

I'm on my second shirt in this pic, the first was sodden by the time I finished installing the Tiller Pin Support Bracket.

Peggy took a couple of pics when I was not looking.







With the Rudder Position Sensor installed, we're ready for the next step. Run the wire from the RPS to the Autopilot Control Unit (ACU) and Install the EV-1 Sensor Core, both those jobs are easy by comparison to this part of the project.

Total time to install the RPS at the Boat -  3½ Hours. Plus the loss of a few pints of sweat equity.

See you on the Water.

Saturday, August 7, 2021

Upgrading our Autopilot - Planning

Planning the Upgrade to our Autopilot

As covered in the previous post (Click here to view), we're upgrading our Autopilot replacing the original unit that suffers from Alzheimer's.

I ordered the major parts as a kit from Defender, added the Rudder Position Sensor kit from West Marine and drew a schematic to ensure I have everything.

Autopilot Schematic
Waiting on the SeaTalkng to SeaTalkng Connector



I missed the cable between the SeaTalkng Spur T's It's on order from Amazon. Should arrive tomorrow (Friday 8/6) so the system will be ready to install starting Saturday.

1st step is to install the RPS Rudder Position Sensor - that will be located in the Aft Locker. It will require some fabrication as the Sensor has to be mounted within certain parameters. There's a great how to article on the Marine How To site. So I'm pretty sure that the first visit down into the Bowels of the Aft locker will be an exploratory run, just to figure out how to mount the sensor. The rest of the install is easy, just mounting the various parts and making the electrical connections.



Here's where I'm considering installing the EV-1 the Attitude Sensor. That bulkhead is about parallel with the Helm Pedestal, the old Autopilot ACU is below the Circled area. Would make for a easy location and out of the way if anyone ever slept in the Aft Berth.

Locating it there would also reduce the amount of cable required to connect the p70s and the ACR / SeaTalkng Backbone.

We were down at the boat today progressing the new Cabin Top Winches, the outside temp was 97ºF but with high humidity is was a lot more painful. So no time to check out the location of the Rudder Position Sensor.

At home this afternoon, I did register all of the Raymarine new parts: Wheel Pilot ST4000, ACU-100, Ev-1 and the Rudder Position Sensor. Their site is not that easy to navigate, it's asking to 'Upload Documents' WTF? So I uploaded a pic of each of the Bar Code strips from each of the units. Then asked Raymarine support if I got it right? The Warranty on all of the products is dependent upon getting the Registration right. Now that's a Get Out Of Jail Free card if ever I saw one. Should have an answer in 3 biz days, that will be August 11th. We'll see.

Saturday August 7th. 2021
Took some pics of the area by the Steering Radial Drive where the Rudder Position Sensor will be located.


This shows the distance from the outer edge of the Aft Locker Shelf support beam (2" x 4") to be about 10" from the center of the rudder post.

That 2" x 4" is not a C34 original, a past owner installed them in order to mount a shelf which covers the Steering Radial Drive and improves the storage of the Aft Locker.

I might touch up the finish of the woodwork and the shaft guide post. Probably use the Same epoxy paint that was used for the bilges last January.


This pic shows the distance of the Radius of the Steering Radial Drive to be approximately  8 1/2" inches

The optimum distance of the Rudder end of the Sensor arm is 5.5" 








Looks like I can drill out where marked in this photo. That will allow a plate to be position on the underside of the Steering Radial Drive.  A piece of Starboard screwed through those holes will make it easier to attach the Tiller Pin.






This shows the underside of the Steering Radial Drive where I hope to attach that piece of Starboard.

The underside of the 2" x 4" aft locker shelf support is not quite level with the underside of the Steering Radial Drive. So a couple of pieces of Starboard will allow the Sensor to be mounted (inverted) closer to the Tiller pin, it needs to be no more than 12" from the tiller pin. So that looks very doable.

Might take a couple of trips down to the boat to manufacture and fit those pieces of Starboard.

So the planning so far:-
  • Rudder Position Sensor can be mounted on the underside of the Aft Locker Shelf support - Stbd side. 
  • Tiller Pin can be mounted on a piece of starboard screwed to the underside of the Steering Radial Drive.
  • The ACU-100 can be mounted where the old ACU is currently installed on the Aft Bulkhead of the Aft Berth as shown in the pic above.
  • The EV-1 can be mounted just above the new ACU-100
  • The p70s Autopilot Control head can be mounted where the Garmin Echo Depth instrument is currently located, we'll have to figure out where to move the Echo instrument. The Echo Depth Instrument can be moved to the Port Side Pedestal wing, we'll just remove the temporary cup holder that is mounted there at present.
Next trip to the boat will be to start on the RPS install, it will have to be early in the day as it just gets too hot right now.

We're planning on taking the boat out on August 16th for a couple of nights, it would be nice to have the Autopilot installed ready for testing on that trip.

See you on the water, maybe not even holding onto the helm.