Gas Bottles Recertification

 One of our Gas Bottles Leaked when at the refill station.

Eximius has two Propane Tanks, they are the Worthington Aluminum 6lb tanks, I had to change out the empty tank on board over the New Year's Eve Cruise and so had to take it to get refilled. The Propane station in Margate reported that the tank leaked, the guy demonstrated the issue. Needed to get a new valve. The Bottles cost over $200 in a good year, right now they are not available and on back order till June 2022.

We normally take the tanks to Ameri Gas in Fort Lauderdale, but when I asked them on the phone if they could replace the valve and recertify the tank, they informed me that they were only able to refill, all of their techs and office staff were out due to the pandemic, sounds a bit iffy to me.

I found the valve online and ordered one, also watched a YouTube on how to change the valve, it was easy, ok, easy in theory, difficult in practice. But with a bit of sweat I was able to change out the valve. 

The tank was new  in 2006, and apparently it has to be recertified after 12 years and then every 5 years. I had both tanks recertified a couple of years ago, but I'm pretty sure it was a rip off, there were no labels applied to the tanks.

The new Valve came from Nash Fuel via Amazon, it arrived ahead of schedule.

I always wondered what the inside of the valve looked like.

The attachment thread is on both the inside and outside of the valve so it fits our older style fitting on board as well as the newer style fitting on our Gas Grill at home.

The new valve installed, now I just needed to get the tank recertified and filled.

We found a company 'Hogans Gas' in Lake Worth that could do the refill, recertification and in a single trip. It was well worth the drive up there.

It cost $30 to get two tanks recertified and the empty filled, the second one was almost full, so they just recertified it and topped it up with Propane.

The guys at Hogans Gas were very polite, helpful and happy to share tips.

It turns out the Cylinders need to be recertified every 5 years from now on.

I'll put a note in my calendar.

As it turns out, I needn't have taken the trouble to change out the valve, Hogans Gas would have done it with a lot less sweat on my part.

So, we're all gassed up for the St. Pats Day Cruise. Hope to see you on the water.

Lost Engine Key

 

We lost our Engine Key

We had just done some testing of the boat's Battery Charging System as it was not charging the house batteries. Part of that test was to see if the Batteries were being charged by the engine Alternator.

I opened the engine raw water valve and Peggy went into the cockpit with the key to start the engine.

Oh! When we got to the boat today, I replaced all of the rusty hatch padlocks with Combination locks and I threw the old locks and their common key in the garbage, just before the garbage collection trucks arrived.

When Peggy tried to insert the key into the engine control panel it would not turn! It was the wrong key.

Did I toss out the wrong key? 

Of course, we have a spare, of course it's on the boat, of course.

Nope! What I thought were spare engine Ignition keys were not (I know, it's a diesel, there's no Ignition, but the key controls the Engine control panel start button, Glow Plug Button, Blower Button and the Panel Lights.)

We dug into all of the obvious places, Nav Table, Key hooks, pant's pockets, I even went out to the car to see if we had put a spare there. During the search for the missing key, I found 3 spares, but they were not the engine control panel key! Grrrr.

Peggy was trying every key we found even those that were obviously not the right key. But one did fit and it did turn and it did allow us to start the engine.

It was at that point that Peggy reminded me. The last time we took the boat out, the engine overheated because I didn't open the Raw Water valve. After that fiasco, I was reminded that some skippers put the Engine Control key on the Raw Water Thru hull valve - to act as a reminder to open the valve before trying to start the engine. I had removed the key from the boat's general key set and put it on a seperate floating key fob so that I could hang it on the Valve.

DUH! We found the key exactly where it was supposed to be, exactly where I was supposed to look.

Today I went to Lowes and had 3 spare engine control panel keys made, we have a second for on the boat, another on my car key ring and a 4th on Peggy's key ring.

I'm guessing we'll remember where the key is next time we want to start the engine.

Oh! The Battery charger - Failed :(  The Zantrax Freedom 20 Inverter Charger is least 18 years old and not worth fixing. I'll post another article about that.

Meanwhile, we can start the engine and charge the batteries because we know where the key is located. 

See you on the water (if we can find it ;)

Paul

Saving Zippers - Thanks Peggy

 

The Zippers on both sides of the Cradle Cover mast wrap were jammed and the Zip pulls would not move up or down and keep the zipper closed! Grrr. Looked like I would need to remove the Cradle Cover (not a simple task) and replace the zips. I have the gear to do that, even have spare zips.

The old zippers are PK #10. I use YKK, I tried to use a YKK #10 Zip pull to replace the PK Zip Pulls but still could not close the zippers. I was ready to start removing the Main Sail and the Cradle Cover when Peggy suggested that we could replace the PK Zip pulls.

Peggy scored an 11 !! I purchased two Stainless Steel PK #10 Zip Pulls online.

When they arrived, I tested one, using it to zip the two sides of  the front panel together, WooHoo! Worked beautifully.

Back at the boat it took about 10 minutes to replace the two old PK zip pulls with the new Stainless Steel items. Another 5 minutes and I had installed Zipper stoppers on the ends of all four zip sides (two each side) 

Thanks Peggy! I was convinced that the zippers were damaged from 5 years of UV exposure, but your idea worked great. 

Gotta love a great boat partner 😍

The Scoop on Poop in Fort Lauderdale

Pump outs are an issue in the Yachting Capital of the world - Fort Lauderdale.

Lack of Pumpouts in Fort Lauderdale Florida

It's a crappy subject but boat owners have to deal with it. It's not something that can be left to rot, it will.

Locally there are not that many Pumpout Stations and there are fewer still that work. For us, the most convenient is at Smoker's Park on the New River just downstream of 3rd Avenue Bridge. We have used that facility many times. There are a bunch of boats that are tied up along the river there, notably, Musette II and a few others, they all have a need for Pump outs. If they don't pump out at that locale, they have three choices:- #1 Call a mobile Pump Out service, it will come to them either at the dockside or alongside their boats.  #2 Go to another pump out station, good luck with that one! or #3 Head out to the Ocean and 'pump and dump'

In our case, Eximius holds a maximum of 25 gallons. In fact, if we had 25 gallons of poop on board, it would probably be making a mess in our bathroom as it would flow back - Yuck! So we pump out frequently. We have the same choice as those boats tied up at the New River:- Use the shore based pump out service (DIY), hail a mobile pumpout, head up to Los Olas Marina (apparently not working and unlikely to be fixed until the rebuild of the Los Olas Marina (Sentex managed now) or we can go out on the Ocean.

Ok, so what is the process if we want to pump and dump out on the Ocean?

It's pretty simple. We head out to the 3 mile limit off shore, normally we go quite a bit further, and open the valve that is normally wired shut, turn on the Macerator Pump and whatever is in the Holding tank is pumped overboard. It might not be obvious to everyone, but on our boat, nothing goes into the head that we didn't eat or drink. No TP, no napkins and very very little fresh water. The salt water flush in our boat has been disconnected. Salt tends to cause cakes (now there's a thought you'll not easily forget) to form in the hoses and the tank.  This means that we create a lot less sewage on the boat than we do at home. A typical flush on our boat is perhaps a pint or two of fresh water. 

So our poop gets macerated before it's discharged overboard. Surprisingly, although the trail of effluent is visible over the stern of the boat, it's no longer visible within a few minutes. A boat trailing us would probably not notice that we dumped if they were sailing more than 3 or 4 minutes astern of us.

Ok, so that's the scoop on poop. It's a sad reality that there are so few public pump out facilities in Fort Lauderdale - Yachting Capital of the World.  Of course, Cruise Ships probably have sewage connections at their docks. I cannot imagine how large their holding tanks must be. HUGE!

Anyway, we have been unable to get out to Sea for a while, issues with the boat etc. But we did get to take the boat out for the New Year's Eve Cruise - Thursday, Friday, Saturday and returning Sunday.

The Smoker's park pump out facility is not working, it's not been working for months. One would think that with all of the Sewage that has leaked into the New River in the past couple of years, literally Millions of Gallons of Poop, that the City of Fort Lauderdale would be making extra effort to provide adequate pump out stations. You would think, Right?

Today we hailed a mobile Pump out company to empty our small (25gallon) holding tank. Chris from Mobile Pump Out Service came to our boat today and took care of business, that's #2. As his card says, they are #1 in the #2 Business.

Chris brought his truck and parked it in the road, ran a hose to the boat and quickly pumped out Eximius. Our tank was only half full and I wanted to rinse off the side of the tank (inside) adjacent to where the Level Sensors are located in order to improve their reliability. Chris was ok with me running a hose and spraying that inside of the tank, he suggested that I also spray the area of the tank that is further from the pump out point near the bottom aft corner of the tank.

Chris' rates are very reasonable, he's a cheerful and sensible business owner. He took care to make sure the work area was clean. I had setup the pump out adapter into the deck fitting. Chris said it wasn't necessary but he was happy to connect his hose directly  to the adapter. Boat owners do not need to install an adapter, Chris has a push in adapter that he normally uses.

So we're MT, no longer full of S#!t even if we did have to pay for the pleasure.  Once the current series of Northerly's pass though, perhaps a week, maybe two, we'll be back out on the water. Of course there's a few little projects to do while we wait.

If you need to get Chris to take care of your #2s, then you can reach him at 954-406-6680 or www.marinewastepumping.net

See you on the water.

Raymarine Auto Pilot - Upgrade review

I'm normally pretty easy on reviews of boat equipment, but I have to step it up with my review of the Raymarine EV100 Autopilot that we installed this year.

The installation - Here's a link to the install process, but here's a quick overview.

• I planned the install in great detail as it was an expensive and complex install due to the existing wiring on the boat.
• The old Autopilot was suffering, turns out it was probably due to bad wiring of the original install whenever that was done, before my time owning the boat.
• The install was done in the summertime here in South Florida - yes - Sweaty work.
• All of the existing navigation equipment was rewired.

After finishing the install a few months ago, we did a dockside test with the boat tied fast to the dock.

That basically consisted of calibrating the Wheel rotation. Once complete we set the wheel pilot to Auto and then adjusted the heading to see that the wheel turned in the correct direction, a simple test, but it sure gives a greater degree of confidence in the complete installation.

Ok, fast forward to the New Year's Eve Cruise on December 30th 2021. We left the dock at 6:15am dawn was just breaking, we navigated down the New River and passed all of the bridges, the last being the 3rd Avenue Bridge, from there is was simple motoring down the river then North on the Intracoastal Waterway, there were only two bridges we need to pass to get us from the River to Sunrise Bay.

I took the opportunity to turn on the Autopilot once we passed the last bridge on the New River. Initially the controller complained that there was no drive unit found, turned out that the Autopilot was not powered on, but the instrument was via the NEMA 2000 Network. Peggy turned on the Autopilot at the Electrical control panel by the Nav Table in the Cabin. 

Now the Autopilot started to obey the commands at the Helm Station. There are 4 heading control buttons:- -1º +1º, -10º, +10º. As soon as the Autopilot was put into Auto mode, the wheel drive motor took control of the Helm. Pressing any of the heading control buttons changed the heading very quickly, it was a quick as if I had manually tried to change the heading by rotating the Helm. I must admit, I was impressed! I was able to navigate all the way from 3rd Avenue bridge to the Las Olas Blvd Bridge - there I took the pilot out of Auto and manually steered through the bridge where the current was pretty heavy and there was other boat traffic the really required manual control.

Again, when we passed the Sunrise Blvd Bridge, I went back to manual operation. After the last bridge, Peggy took the helm with the Autopilot in Standby.

The old Autopilot would very slowly react to a heading change request and would often just stop steering, it was not reliable. We tried to steer via the Autopilot but had to keep a close eye because it deviated from the desired heading every few minutes. The Helm wheel would move with exaggerated turns and confidence in the Autopilot system was zero.

The new Autopilot is amazing so far! It responds immediately to a heading change request and does not make exaggerated wheel movements, in fact they are quite fine movements. We have had other people sail on Eximius, and they would not make such fine movements of the wheel despite instructions on how to hold the wheel and make small but early trims of the wheel to keep on course.

Beneath the digital heading display on the Control Instrument, there is a text bar that indicates when the system is detecting local magnetics, every now and then it would change color but it pretty much stayed visible on the first day of use.

After a great New Year's Eve cruise with the Hillsboro Inlet Sailing Club, we left Sunrise Bay at 7:15 Sunday Jan 2nd 2022. Once past the Sunrise Bridge, we put the Autopilot to work again and easily navigated to Las Olas Blvd Bridge, manually steered past the raised bridge and then back into Auto.

As we continued up the New River, we heard from the FEC Railroad bridge that it was going down in 6 minutes. I called the bridge tender asked how long he expected the bridge to be down. 14 minutes.

At the rate we were travelling though the flooding river, we would be at the FEC bridge before it opened. So I decided to do a few Doughnuts downstream of the 'Tunnel' to pass some time in order that we don't end up trying to hover back from the approaching bridges. I probably made 5 or 6 doughnuts, just turning to Stbd by adjusting the heading via the Control instrument. 

During this maneuver the Control Instrument display changed completely. It displayed a message stating that the system had completed the Magnetic evaluation. WooHoo.

After accepting that info (OK) the screen returned to the normal display and the Detecting Magnetics notice was no longer visible.

We have yet to complete the Commissioning process and that requires that we are in an area that is free of obstructions (like the sides of the New River!) as we have to let the Autopilot take charge.

The Autopilot has a learning curve (the pilot, not me!) and during one phase of the commissioning process the Autopilot follows a track similar to the one shown here. We'll have to be on the Ocean to do that, it's far too crowded on the New River and ICW and the lakes are not big enough as well as normally being occupied by many boats.

I'm good with this, another reason for getting the boat out.

So far, my impression of the EV-100 is Excellent! Easy to use, Very Responsive and very conservative in the way it manages the steering.  We have a lot to learn about the system after completing the Commissioning including being able to follow a track (not sure if it will do that, but it has the systems required, just have to make sure that the Raymarine part will listen to the Garmin GPS Chartplotter which provides the data for following a track.)

Right now, I give it a **********, 10 out of 10 stars. I am delighted with the upgrade. Well worth the effort and we both look forward to using it often.

Oh! One last thing! 

Prior to installing the new Autopilot (which includes a Rudder Position Sensor) we had to look down between our legs to see which way the Rudder cap was pointed in order to determine the Rudder Position. It was almost comical, Peggy would be at the helm, I would ask her to go Amidships and she would look down between her legs and turn the wheel till the rudder cap pointed directly forwards.

The New Autopilot has a Rudder Position Display, even if the Drive it not powered up.

The display shows a Red (port) or Green (starboard) block from 0º to current rudder position. 

No more looking between our legs to see the Rudder position. BTW this was only necessary because the wheel required more than 1 turn to move the rudder from fully to port to fully to starboard, so the whipping that we have on the wheel to indicate Amidships is only useful if the rudder it nearly Amidships already. 

Stay tuned for more updates as we complete the Commissioning process and get used to using this awesome upgrade to Eximius.

See you on the water. 

2021 New year's eve Cruise 12/31

Friday - 12/31st

A great night's sleep, bodes well for the end of 2021.

We slept in but got up long after Sunrise and I got busy making Coffee before breakfast.  Today's fare was Sliced Ham Steak, Fried Eggs, big Ohio Tomatoes and whole wheat skillet toast. Brie for Peggy's Toast,  Spread, peanut butter and blueberry preserve and, of course,  some hot Coffee. 

Another beautiful day in South Florida, clear skies, temp in the 80`s surrounded by boats, suitably anchored. 

Phone calls started to come in notifying of club members on their way to the Bay. Soon the bay was getting crowded.  Overnight were Spruce Goose next to us, O'Hara and Affection. During the day Hullabaloo, Endurance,  Diversion, Commotion, Pegasus,  Swan Song, Sea View and a guest of Commotion. A good turnout for an end of year cruise that is still hampered by the continuing Covid 19 Pandemic. 

Mike and I took our dinghy out to visit with each of the boats that arrived before 3:30pm, we were chatting to Tom and Norma on O'Hara when Commotion turned into the Bay and that caused a bit of a Commotion as they were going to raft up with us, Eximius &Spruce Goose and we were not aboard for Commotion's arrival! Ross was at the helm of Commtion, Mike & I cast off from O'Hara and zipped around the front of Commotion to the back of Eximius.We quickly got over to the Stbd side of Spruce Goose just in time to accept the lines that Astrid had ready on Commotion.  10 minutes and we had our three boats secured.  Not long after, Ross' buddy arrived in his trawler and thar was quickly secured. 

About twenty minutes later,  Mike and I dinked the Trawler's anchor and rode to about 100 ft ahead of it's bow. Now we had two anchors holding our 4 boats and the known good holding as well as the good weather forecast overnight should mean another good night's sleep. 

OF COURSE IT'S NEW YEAR'S EVE!

There were several boats open for Sundowners, just about everyone is ready to socialize after this year.

It's now 21:30, we can hear fireworks from most directions, not many, but I'm sure that will not last. We're planning on making some noise at midnight. Unusually, it's not gust to welcome in the new year, new resolutions and aspirations,  but to say a loud and very clear Goodbye to 2021. Here's to doing our best to make 2022 a better year.

Wow! I actually stayed up till next year. 

OK, time to turn in without waking Peggy.

Thanks Ross, Astrid, Mike, Scotty and Gladys for the champagne and upbeat wishes for the new year. 

Let's all work on making 2022 better.

New Year's Eve Cruise 2021

HISC New Year's Eve Cruise 2021

As this is the last cruise for our sailing club in 2021, I really did not want to miss it. The weather cooperated we did a clean up of the boat  and we loaded the boat after it has sat for the last 5 months not doing much except go moldy. As the boat sits on the Dock facing East / West, the Port side of the boat is on the North side, away from the dock. Just like Trees  in a forest, the North side of anything left close to water will grow green, quickly! Despite our attempts to clean the boat every few weeks, that's all it takes for the damp atmosphere to encourage green growth on every surface that does not face the Sun. We spent a good effort scrubbing the boat down, focusing on the Port Side. Grrrrr!

With the boat fully loaded by end of day Wednesday, we planned for an early rise to get down to the boat before high tide at 6:30am. An early night for the 4am alarm and we quickly put the last few things together - clothing, Peggy's Travel Guitar, and our tech stuff - Computer, Tablets, Phones plus a thermos of Coffee.

We love this coffee pot, our daily brew is made (drip funnel) in this pot every day. It really does keep the coffee hot all morning and warm enough to drink for the rest of the afternoon.

The plan was to get down to the boat, leave the dock at high tide and then have a hot cup of the best coffee (that's almost any coffee while on the boat) but it didn't quite work out that way.

Despite leaving the house nearly 30 minutes later than planned, we were ready to pull away from the dock by 6:15am - All instruments installed (we don't leave them at the helm when we're away from the boat), all lockers unlocked for quick emergency access and all lines set to dry on the dock while we're away for the weekend. Engine running, last line cast off, FBFL (flash light) in hand to help guide our way down the dark canal, our EarTec headsets saved us having to shout directions as we quietly motored, barely making a ripple as we headed for the deeper waters of the New River at the end of the canal.

As we approached the bend before the 11th Avenue Swing Bridge, still in darkness, we called the bridge on #16 requesting an opening, the Tender was on the ball and started the opening. All this time I was on the Bow guiding Peggy as we made the turns down the still river. Not quite dawn, I had the FBFL shining ahead when Peggy noted that the engine temperature was rising beyond it's normal 148ºF 

The bridge had started it's opening, I dashed below realizing that I had not opened the raw water intake thru hull valve, my screw up!  Quickly opening the valve and expecting the temperature to start to drop as river water was pumped through the heat exchanger and the cooling cycle would do it's work.

It didn't! The engine temperature gauge was still heading up. It was above 180ºF now. I was pretty sure we could get through the bridge before the engine started to complain, but we didn't. We did get through the bridge, but the engine high temp alarm was sounding, it's not really loud, just sounds that way! Way Loud! I was at the bow and prepped the anchor to drop. Peggy steered us out of the channel center so that we could anchor and I dropped about 50' of chain, we were still moving and I had a challenge to keep control of the chain as the anchor dug into the soft bottom, but we did OK, Peggy shut down the engine.

Step 1: Check the raw water valve just to make sure I had opened the correct valve, it was open. I loosened the hose clamps that secure the hose to the thru hull valve. Closed the valve, removed the hose to the filter, opened the valve and confirmed that the water way was clear from outside the boat.

Step 2: Check the impeller - it could have seized or separated from the pump shaft. Quickly got my tools out and removed the face place from the front of the Oberdorfer Pump. The Pump was dry but the impeller looked ok. Squirted some water in the impeller area and closed up the pump, Peggy restarted the engine. I expected that if the water was flowing, the engine would almost immediately start to cool down. It didn't! 

Step 3: Change out the impeller, I always keep a couple of spare impellers aboard. Removed the plate again, this time the body of the pump was full of water. I still tried to remove the impeller and replace it but could not get the impeller off of the pump shaft --- - Note to self! Carry a spare Impeller Shaft with the spare impellers.  Thinking that as the pump was full of water, it had actually started to pump. So I replaced the old impeller and it's shaft into the pump housing, closed up the plate and asked Peggy to restart the engine. She did, it did, and cooling water was pumping out of the exhaust just as it should.

By this time it was gone 7am and we had to get through the bridges before 7:30am when they shut in the down position until 9am (rush hour road traffic). We approached 7th Avenue Bridge, called the Tender and he opened without any delay for us. Now the 'S' turn through Sailboat Bend  on the approach to the FEC Railroad bridge, we were expecting it to close at 7:10am and heard them on the radio announce that the bridge was moving (couldn't make it out to clearly) but we really wanted to get past that bridge so that we could get past Andrews and 3rd Avenue bridges before the shut down for the rush hour. I called the FEC Bridge asking if they could hold open for just a minute longer so that we could clear that bridge. I had misheard the bridge Tender, she had reported that the bridge was going up, not going down! Phew! As we approached the bridge with one vessel ahead of us, it began to go up and were able to clear Andrews and 3rd Avenue bridges. You bet I wished them all a Happy New Year!

Once past 3rd avenue bridge, Peggy went below and powered up the Auto Pilot. Oh Happy Day! It works like a charm! I was able to steer all the way from just before Tarpon Bend to Las Olas Blvd Bridge using the Auto Pilot. Just had to press the buttons to add or subtract 10º of heading and the boat quickly changed to the new bearing. I was impressed! With a 10º change in bearing, the boat would respond almost immediately. It was less noticeable when I changed by just 1º of 2º but it responded correctly and quickly all the same.

Once past Las Olas Blvd Bridge, we followed another sailboat under power up  to Sunrise Blvd Bridge which opens on the Hour and Half Hour. We made it easily and I used the auto pilot to steer appropriate course changes to avoid boat traffic coming the other way.

Peggy took the helm as soon as we passed Sunrise Blvd Bridge and went forwards to prepare the anchor. Sunrise Bay was pretty crowded, there were 7 big boats already in the Bay and ourselves and the boat ahead of us made it a crowd of 9. Mostly larger Catamarans. So we snuck into the North West Corner of the lake well clear of the other boats, but a bit too close to the homes at the edge of the Bay.

Time for breakfast: Cereal and Coffee, we had a cup of coffee and a couple of slices of Toast before we home this morning. Peggy was pooped, I was not far behind not having slept too well Wednesday Night. Nap time. I awoke to some boat noises and peeked out of the cabin to find that a couple of the bigger boats that had been anchored near the middle of the Bay had gone! Great! Let's haul anchor and move so that we have more room when our buddy boats raft up with us Friday. It only took a few minutes for us to start the engine, done our headsets, haul the anchor and move just a couple of hundred yards to the better anchor spot. Now we can relax.

Of course, we didn't, relax that is.  Ok, so Peggy hit the nap sack but I started to prep the boat for continuing to scrub it down and get rid of the remaining green stuff.  I turned the Dinghy over and added some air, it had been upside down on the dock for how many months? Once inflated, I raised it with our Utility block and tackle and put the dink over the side. Then I cleared the decks ready for some scrubbing.

It took an hour, by which time we were both ready for lunch - Left over Chicken wings from Wednesday's lunch and some Potato Salad washed down with a hot cup of coffee. Yes, it was still plenty hot.

After lunch, I spent another couple of hours scrubbing the Port side of the cabin top, it came up pretty good and that was enough work for the day.

Ok, I rarely sit idle on the boat. The Radar data connection to the Chart Plotter was showing signs of wear (it really was bent in too tight a radius), that got fixed with some Rescue Tape. The cabinet in the bathroom was not properly attached since the last time I removed it. I took the chance to check on the fuel tank and it's drip cloth lead detector. All's well. Lastly, I had started on the install of the new Nav Station goose neck lamp, so I completed it's installation leaving just the electrical hook up for another day.

The new lamp should not only illuminate the chart table, but also the inside when the table top is raised, something the old lamp could not do.

That was it for the day. Time for a Rum & Ginger, a glass of wine for Peggy and watch the other boats come and go, there's always something that happens that deserves the remark: Glad I didn't do that!

Before dark, Tom & Norma arrived on Ohana anchoring off our Port Side - hope they realized how pretty Eximius looked, at least forwards of the Cockpit.  Jeff & Judy on Affection arrived before dark too, they anchored off our Starboard Stern quarter.

We had a simple dinner of Pasta and Source. Peggy played her guitar despite having had a glass of wine. We both had showers. Desert was a Klondike Bar and another glass of Rum & Ginger.

To close out the day, I wrote this blog article.

Today's "Gotado List" includes:-

• Install an Engine Area Lighting fixture - can't see squat when it's dark outside.
• Install a Cockpit Light - it would have helped when we were setting up the instruments in the dark this morning.
• Apply new Shoud Turnbuckle Cover top end Tapes - the old tape has long gone.
• Get a decent head lamp, I could not see the keys when trying to unlock the boat lockers (3) in the dark. Yep, we haven't made a dock departure on a long while --- if ever!
• Get a new service kit for the bathroom toilet  --- we used most of the spares last time we were out, how long ago??
• Get a new Camera mounting - the old one is so corroded that it will not tighten enough to hold the action camera in place. 
• Relocate the Mini Inverter - I had to remove it from it's home in the aft berth as it was too close to the newly installed EV1 sensor for the new Auto Pilot.
• Replace the Starboard Bow Nav Light. - The port light is fine, the Stbd one is not. Might be just a new LED lamp that needs replacing, I have spares.

Ok, it's 9pm, that's it. Hope to get some great pics tomorrow as the other club members arrive and we prepare to celebrate the end of 2021 and the oooooh can't wait to make 2022 a better year.

More tomorrow!

Paul & Peggy aboard Eximius.