Wednesday, January 30, 2019

Pre New Years Eve Cruise

This year's New Year's Eve Cruise is at Lake Boca

Because of the tide times, we decided to spend the night at Lake Sylvia after an easy motor from the Dock.

The following morning, we left the lake early, it was low tide and we nudged the bottom despite hugging the East side of the canal. As we headed out of the lake, there was a Forty something sailboat listing heavily, they had an 8' draft and were way to close to the canal center line even at high tide. They acknowledged that they had about a 5 hour wait. Hope they got off easily without any damage.

We motored up the ICW, making all of the bridges, we did cut it too close to the inside bend before the Hillsboro Inlet Bridge and came to a smooth, sandy bottom, stop. It was a none event, we had turned towards the deeper part and easily motored off. Gotta pay attention

Diversion was already at Lake Boca when we arrived, not many other boats, so we had the pic of anchoring spots. We backed down hard knowing the weather might kickup over the weekend.

As the afternoon wore on, more of the club boats arrived and we prepared for the Champagne Party that evening aboard Into the Blue and Chesshire.

We took a dish of appetizers made at the last minute from what we had onboard. Cocktail sticks, Cheese, Grapes, Slice of Ham on  a piece of Cucumber. Worked out great, they disappeared.

We took a dink ride over to the park and Peggy practiced her Dinghy exit plan - success, her workouts are having a very positive effect, we even went for a 20 minute walk to the bridge and around the park. We also dumped our trash. There's Water at the park if we had water containers to fill.

Sunday We had the chance to chat with Halabaloo and some friends of  Jeff Miskin's but everyone else abandoned the lake by Sunday afternoon. By Monday we were one of the few boats left on the lake despite it being New Year's Eve and the promise of a great fireworks display close to the lake.

So we left the lake Monday morning and took the inside route back to the slip. We were home with time to prep dinner of Crab Cakes (Thanks Shawn!)

A fun weekend, even if we didn't get to sail. But I'd rather be on the boat under motor than mowing the lawn!

Looking forward to getting out there, hope to see you on the water.

Next Club trip is the Chili Cookoff on Feb 9th.

Meanwhile, we're still prepping for our trip to the Abacos in March/April.
Shopping list includes:
  • AIS Transponder (replacing our AIS recever)
  • New Fishing Gear: Rod, Gaff, Lures, Fillet Knife.
  • New Cabin lighting to replace those that have failed in the past few months. (Galley lamp, Reading lamp, Aft Berth lamp).
  • Holding tank Beckson access plate (I know, never want to use it but need to clean the tank)
  • Add rail tubes Port and Stbd sides for Fuel & Water tanks.
  • Purchase 4 x 6 Gallon Water tanks
  • Make Covers for new Water tanks and remaining Fuel Tanks.
  • Top up Propane tanks (1 is already full)
  • Clear up the Tool storage area to enable Non-perishable food storage.
  • Gearbox Oil Change
  • Clean out Water tanks & replace all water filters (3 on the boat 1 on the boat refill assembly)
  • A few other things that might get done - crack the list above first.
Sailing - It's fun even when it's just time preparing.

See you on the water.

Saturday, November 10, 2018

Upgrading the Mainsheet Block System

Yes, we're still making improvements to Eximius and this one is a long time coming.

The Mainsheet (the line that controls the position of the Boom) runs through a total of 9 Sheaves (the pulleys inside a block) and 7 of those are original to the boat, so they are going on 31 years old. I have cleaned and lubricated those blocks many times, but it really does not make much difference.
Normally, the crew will 'play' with the Mainsheet and the Traveler to keep the sail shaped appropriately with changes in the wind.

To explain how bad the blocks work: In order to ease the boom from the centerline, even when the sail is full of wind pressure, we have to ease the Mainsheet by pulling on one of the lines in the Mainsheet block system and then letting it go so that the boom moves and takes up the slack. In order to move the boom back towards the centerline we have to use a winch! Consequently, we often position the Mainsheet and let it be, even if we need to move the sheet unless it's a significant sailing status change like from Close Hauled to a Beam Reach..

This means that we don't get the best speed from the boat! We updated the Traveler a while ago and that does give us a decent amount of change but it does not encourage correcting mainsail twist, and hence boat speed.

Scouring the Internet for replacement blocks, with a preference for Garhauer equipment, matching the new Traveler and new Deck Organizers, I was dismayed at the pricing, it looked like we would have to pay around $650 for the set of blocks, Dang! and we're watching the pennies as we had to buy a new truck earlier this month.

Peggy asked what kind of blocks were sold by Catalina Direct for the C34, hadn't thought of that! A quick review of the CD site and I found they had a C34 Mk1 Mainsheet Block Kit for $266.
Image from Catalina Direct

The kit comprises

  • 3 Single Blocks with Shackles
  • 1 Single Block with Shackle & Becket
  • 1 Fiddle Block with attached Single Block with a shackle on the Fiddle Block
When I called Catalina Direct, they confirmed the blocks were Garhauer Blocks - awesome!

I didn't need the 3rd Single Block as I had replaced the block at the base of the mast already.

The cost bottom line was $246.70 for the kit and shipping after the discount for not needing the 3rd Single Block. The new block kit is on it's way and should arrive by late next week.

Peggy is pleased because we have been discussing sail trim a lot recently and it would make a huge difference if she could adjust the Mainsheet, and this kit should enable that.

I'm hoping that the end of the sheet, which attaches to the becket in the middle block on the Boom, will easily transfer to the new becket, else I'll have to re-splice that eye. The rest of the Mainsheet should just thread through the new blocks.

Here's a pic of the completed installation. 

I didn't need to make a new eye on the end of the Mainsheet, it fit the becket on the upper middle block just fine.

The astute will notice that there is a twist in the sheet (black & white rope) at the additional block on top of the Mainsheet fiddle (click on the image to zoom in) That's because that extra block is from the old setup and is too big! The kit was sent without the extra block because they were out of stock for that item, it's slightly smaller than the old block and it will not be on a swivel.
A nice feature of the new blocks: The shackle pins are threaded into the shackle and have a securing ring though a hole drilled through the threaded portion of the pin. I much prefer this setup to one where the pin is secured only by the ring. Nice job Garhauer!

The difference in friction between the old setup and the new, with the passing through 9 blocks and 1 rope clutch, is staggering! I can now ease the Mainsheet by opening the clutch and then applying a few ounces of pressure on the boom (which would be done by the wind on the sail).

We have a working Mainsheet! WoooHoo! Of course, we're not sailing for at least another week!

But we'll see you on the water!


Update: Tuesday 11/20/2018

Great news! The additional block for the Fiddle arrives today, so we should be able to install it prior to our sail up to Lake Worth on Friday.

Not only handsome, but it looks really well made and the sheave almost floats on it's bearings.
This, non-swiveling, block should also eliminate the twist in the last part of the mainsheet, an added benefit.

Not sure if we're going to make it to Lake Worth this weekend, bummer! But we'll go down to the boat and install the new block, that will finish off the new Mainsheet Block System.

Sunday, November 4, 2018

Getting Rid of the Rain Water

Keel Stepped Mast = Occasional Rain Water in the Bilge

In a recent edition of the Mainsheet Magazine for Catalina Owners, Seth Martin had written a great article about building and installing a Bilge pump system to cope with those small amounts of water that end up in the bilge, basically what would be left over if the Automatic Bilge Pump ran, perhaps a Gallon or two over a number of rainy days.

Currently, we manually hand pump out the rain water and then soak up what the pump cannot get with a few diapers and finally dry the bilge with a few paper towels. I did purchase a battery operated fluid transfer pump from Amazon, but when it arrived it was marked up as an Olive Oil Transfer pump. It might work for Olive oil, but it sucks (pun intended) at pumping water!

Just to show what we're talking about.

Here's a pic of the #3 Bilge area (#1 is in front of the mast,#2 is immediately behind the mast and has the Bilge Float Switch sitting in the bottom, and this one is #3 which has the Bilge pump attached to the bottom

The water is after a few days of rain. We pumped this out by hand and then dried it up with a couple of diapers (our Grand Daughter no longer needs them 😀

It's about 3/4" and there's a similar depth in each of the other bilge areas.

There are commercial products on the market, but when I have the chance of another DIY project, that causes me to get excited. Seth's system is brilliant.

Basically the System consists of a small water pump, a digital timer to control it, some tubing and pickups all fed to a manifold connected to the Pump inlet, the Pump outlet fed to an overboard drain.

Eximius has 4 Bilge areas each connected by limber holes or tubes, so each needs a pump out.

So, first thing was to investigate the pumps available. I elected to purchase this SeaFlo Type 21 12v Diaphragm Pump on Amazon.

It arrived early :)

A quick connection to a 12v power supply to check that it ran and all is great.

It has an Automatic Pressure sensing switch but i it can be bypassed.


Then I spent a while picking out a timer. I found this 12v Digital Timer with on/off control.

Found this one, again on Amazon.

  • Rated Voltage: 12V DC; Contact Capacity: 16A
  • Full Time Range: 1Min-168 Hours; Programmable: 17 times/week or day
  • Internal battery: 1.2V/40mA (rechargeable batteries)
  • Power failure memory: 60 days; Operate Temperature: -10 to +40 C
  • Dimensions: 60x60x32mm; Net weight: 80g


Next, I needed to find a way to hold the Drainage Pickups that have to be installed in each of the Bilge Spaces. I could not find anything ready made, but was able to make them using an Electrical Installation Box from ACE hardware,

I figured I could cut them to create brackets that would hold the pickups in place but also allow for future sponge replacements.

A few minutes with a Back Saw and then clean up the edges with a Stanley knife and they are ready to go

The slot in the lower edge will allow me to push the Pickup tube in place with the Sponge below the bracket.

$0.79 x 2

In the pic, There are 4 Red & Black left over drip assemblies from a Harbor Freight Garden Drip System, I knew they would come in handy one day. All I had to do to make them suitable to act as Pickups was to cut off the barb on the Red End.

The Sponge pieces are about 1 1/4" Square with a hole pushed through with a Screw Driver.

The Black Plastic 3/16" Tees are also left over from the Drip system.

On the Left is a completed pickup, that will connect to the Pump input manifold (that will be made from Tubing)

This shows a Completed Drain Pickup with the Tube in the Bracket Slot ready to connect to the Pump Input Manifold.

Plan is to Glue the Bracket to the side of the bilge with just enough room beneath it to be able to slide the Tube & Sponge out so that I can replace the Sponges in the future.

I'll probably use 3M 4000 to secure the bracket in place.

So far so good.

Here's what the Pickup looks like from underneath.

I did a test using two of the pickups connected to the Pump via a 30' long piece of 3/16" tubing. They were placed in a small tub (Butter Spread Tub) with about 2" of water in it.

Then I ran the pump connected to my 12v power supply. It drained the Tub in less than a minute, and the Tub was basically dry, certainly dry enough to evaporate naturally.

Seth's project seems to be very suitable. He installed his in a Catalina 25, The bilge areas on our Catalina 34 already have quite a bit of equipment in them: Bilge Pump Control Float, Bilge Pump, Bilge Pump Hoses, 2nd Bilge Pump Hose, and finally Keel Bolts.

So my pickups are quite a bit smaller than those that Seth made for his boat.

The Boat's Main Bilge Pump has 1.5" tubing running from the Pump to the Overboard Discharge at the rear of the boat, that's about 25' of hose! When the pump stops because the water level is too low, the water in the hose floods back into the bilge. New Nearly Dry Bilge System will pump that water out.

However, I'm concerned that the hose from the Pump to the new Overboard Discharge vent will also be able to flood back into the bilge when the pump turns off at the end of it's 'Pump On' period. To prevent that, I'm going to install a One Way Water Non Return Valve in the discharge tubing near to the Outlet of the Pump.

With that installed, when the pump turns off, any water in the discharge hose will simply stay there, although, if the pump runs when the bilge is empty, then it will blow any water that is in the discharge hose out of the overboard discharge vent.

After several experiments, I came up with this solution.

The Pickups will be larger than originally prepared as per the pics above. The Pump will be attached to a Starboard Plate with 4 Stainless Steel Thumb screws (ACE Hardware) and the suction side will be from the middle of the two forward and the two aft pickups.

The Output of the pump will be attached to a new Vent that will be installed below the existing Aft Fresh Water Tank Vent that exits into the Cockpit beneath the Auto Pilot Control head. I'll add a non-return valve just upstream of the Pump output line to prevent water in the line from flowing back into the Bilge via the new Dry Bilge Pump.

The wiring of the Pump is pretty straight forward.

The Timer switch will have a 2amp fuse to the Bilge Pump Circuit before the Circuit Breaker - that way, if the timer fails and blows the fuse, it would not blow the bilge pump power supply - Bilge Pump is essential circuit

-ve from the Timer Switch Power Supply to Ground

-ve from the timer Switch to Ground.

So if the Timer or the Pump blow the fuse, the Circuit breaker that provides power to the Main Automatic Bilge Pump will remain live.

Ok, installation complete.

Final install was slightly different from the above as the blue pickup holders were not necessary. The pickups and sponges stay in place without any additional support.
The system has been running for two weeks and our bilge is DRY!

I have programmed the timer to turn the pump on for 1 minute every 2 hours during the day and 3 hours during the night. So far it's working perfectly, the bilge is totally dry. Time to clean the bilge and make it look pretty.

Of course, this is November, dry season here in South Florida, but we tend to have rain every couple of weeks, it rained yesterday and again today. I'll keep a watch on the bilge pump counter and on the state of the bilge itself. 

So far, I'm really pleased with the way it's working. Having a totally dry bilge is a big deal! 

See you on the water.

Sunday, October 28, 2018

I find Whips Sexy

Boat Whips that is!

In the ongoing campaign to keep Iguanas from pooping on Eximius at the dock, we were suggested installing Boat Whips. As it happens, a friend of ours is selling their boat and the whips were not included - She offered them to us for Free! Would not accept payment so I promised some of my home / boat baked bread when we are nearby.

Taking the whips home with about 12' hanging out of the back of our F150 was a little nerve racking, but I tied two bright flags to the end of the whips so that any following vehicle could see them, that worked! Each time a vehicle approached from behind, they stayed well back!

At home I sanded down the aged fiberglass splintered whips and applied a half dozen coats of Krylon Spray Paint  - Mahogany Red! Wire brushed the flaking paint from the base plates and sprayed them Black. For aged whips, they now look pretty good.

The bases are secured to the decking with 4" 1/2" Bolts and Nylock Nuts & Fender washers underneath the deck. I cut a piece of 1/2" thick rubber floor tile so that the bases would not cut into the deck planking.

Getting the washers & nuts onto the bolts below the deck was a challenge, but a decent amount of sweat and puffing got them done.

The line that came with the whips is in pretty good shape, but was too short for this setup, so I extended the line with some spare from the boat - all boat owners tend to have 'extra' line onboard!

The Whip line is secured to a cleat on the whip at the dock side and onto a cleat nearest the dock on the boat.

We normally have the boat facing East, but it's facing West right now as we didn't want to turn the boat upon our last return to the dock, simply because we wanted a quick unload and get home for a nice shower!

The Whips hold the boat nearly 2' from the dock unless the wind is from the North, which does happen, but mostly it's from the East. When wind is from the North, the boat moves towards the dock and then eases off again, we'll have to practice adjustment of the whip lines in order to find the optimum position.

Thanks Eileen!

See you on the water!

Tuesday, October 23, 2018

HISC Sailing Social 2018

Each year the HISC holds a Sailing Social, basically a bunch of members go out on their boats following a 'leader' and navigate in ever decreasing circles - ie. going nowhere.
But every boat has at least one person with a camera that takes pics of all the other boats, then we share them after the weekend.

For us, the weekend meant we had to leave the dock Friday at 5:30pm in order to miss the bridge lockdowns and get past the shallow end of our canal before low tide. So we spent the night at Lake Sylvia. We had Sausage and Veggies for dinner, we didn't run the generator, thinking that the cool breeze would last all night. It didn't!

Saturday morning, we pulled anchor, left the lake and headed out to the Ocean via the Port Everglades channel, it was a beautiful day for sailing! We headed casually North East to the 3 mile limit for a pump out, then turned towards Hillsboro Inlet's outer marker (the HI Buoy) to meet up with the other members, I think most of them came out of the Hillsboro Inlet.

Here's some pics.

After the 5pm end of the Sailing Social, we sailed towards the HI Buoy then into wind, dropped our sails and motored into the Inlet for the 5:15pm bridge opening then headed North up the ICW

We arrived at the Hillsboro Blvd Bridge just in time for an opening and then motored up to the Camino Real Bridge, but that bridge is being rebuilt and right now, it's open with both leaves of the Bascule Bridge up, so we were able to just motor through.

We met up with Paul & Leanne McKissick in Lake Boca and could smell their dinner cooking in the BarBQue on the back of Margarita.

That night we ran the Generator until 1am, I could have let it run as it ran out of gas 20 minutes after restarting it in the morning to charge batteries.

By 10 am we were heading down the ICW towards the Hillsboro Inlet, saying bye to Paul & Leanne although I don't know if they heard us.

Out on the Ocean it was another gorgeous day on the water, ideal for sailing. We had a great reach all the way down to Port Everglades, sails down, motor in and back to Lake Sylvia where we just hung out until 5:30pm. Hauling the anchor we took an easy motor up the New River, back to our slip and the quickest unload ever, thanks to taking the time while sitting in Lake Sylvia to unload the Fridge/Freezer, bedding, and all the usual stuff we bring home, including the broken flag pole for repair.

Awesome sailing weekend, we'll definitely be doing that again in 2019.

See you on the water.

Octoberfest 2018

Ok, let's make this one quick.

The HISC's Octoberfest was held on Sunrise Bay, just North of Sunrise Blvd Bridge on the West side of the Intracoastal Water Way. (ICW)
We had at least 15 boats attend and several more club members arrived by water taxi (Dink Rides), some of us arrived Friday (extra Cruising Point) but most arrived Saturday in time for the EXCELLENT cruise dinner of Brats, Red Cabbage and Roasted Potatoes followed by some awesome deserts and, of course, beers for the sailors.

Hosts were Intermission, Imagine and Wind Punk. 
On the bay that night were: 
Eximius, Diversion, Intermission, Wind Punk, Cheshire, Alebjie, Dalcarlia, Affection, Pegasus, Imagine, Lady Gray, Fandango, Haven (Cookie Monster - Eduardo's new boat), Po Poki II and Duet

Many of the club cruises include a 'best dressed' competition, resulting in prize for the best Gals Costume, Best Guys and Best Couples costumes.

Here's the winner:

Costume from Amazon, Hair by Peggy, Dinner by Cheryl, Fun by HISC.

See you on the Water.

Wednesday, October 3, 2018

Annapolis Sailboat Show 2018

Annapolis - Just for the fun of it.

We went to Annapolis in 2013, it rained! Every Day! But we really enjoyed the visit. On that trip we visited the US Naval Academy, The Boat Show, and local antique store and museums.

We're hoping the weather will be better this year and are looking forward to the Boat Show, the Blue Water Brokerage Show and, hopefully, the Maritime Museum and possibly the Chesapeake Bay Museum. We also hope to meet up with a few of the HISC members and even with some old 'online' acquaintances from the Catalina 25's Association. We're only there 3 full days, flying in Thursday afternoon and flying back on Monday around Noon.  

The Blue Water Brokerage Show is being sponsored by David Walters Yachts, Josh McLean, a HISC member will be there. Amanda Hyatt Haley, another HISC member, from Dennison Yachts will be at the Boat Show, so we should recognize a few people, but I'll make sure to wear my HISC Caps and Shirts just in case!

We're staying at the Annapolis Westin, and will get either an Uber or shuttle from there to the shows. That also means I'll have my cellphone charged and on for the entire trip which will help with casual meet ups with our friends also in the area.

See you there!