Thursday, June 16, 2022

Victron System Install - making progress

Victron System Install - Making progress

Braving another hot day down at the boat, I made a lot of progress.

It was sweltering today! Even with the portable cabin fan running full throttle, it was only just bearable, the fan was basically blowing hot air.

On the up side a couple of successes. Completed the wiring of the Multiplus to the new Disconnect Box, mounted the Disconnect box to the bulkhead and tidied all of the wire - cable management - so the work area looks much better.  Also completed the wiring from the Multiplus to the Electrical Distribution Panel, that was fun, especially the ground connection that is to a terminal block just beyond arms length when leaning over the Nav Table. but I got it done.

Made a call to eMarine about connecting the Cerbo GX and the GX 4G LTE modem directly to the spare + & - studs inside the Multiplus, they confirmed it was not only OK but quite a few installers have done that as the Cerbo GX is often placed pretty close to the Multiplus.  I also asked about the provision of suitable wire for the grounding of the Multiplus, they have it and I'm picking it up in the morning.

So after a very busy morning, here's the list of wiring to be done tomorrow.

  • Install new Ground Wire from the Stud on the underside of the Multiplus to the Grounding Terminal Block in the engine bay.  This will involve using a wire fish/snake to reach from inside the Bathroom cabinet up to the electrical panel area where I drilled a new access hole. The wire will be #2AWG
  • Install new Trickle charging cable from the Multiplus to the Start Battery  - the old cable was the wrong AWG and it was also household wiring! The new wire will be #10AWG Red Stranded tinned copper wire.
  • Install the new Reverse polarity lamp test switch in the Disconnect bod. I found out today that the old Reverse Polarity lamp test switch was incorrectly wired and it only provided power to the lamp when the switch was depressed, when not depressed, the lamp was not provided any power so it would never light! Grrrrr.
  • Connect the Temperature sensor to the House Battery bank
  • Connect the Smart shunt power supply wire to the House Battery bank
  • Connect the Main House Battery wire to the battery bank
At that time the boat's electrical system should be alive and happy  - I'm deliberately not saying 'humming or 'kicking' for obvious reasons.

The last part of the install - not counting the update of the system firmware and the activation of the GX 4G LTE Modem and it's connection to the internet, will be the configuration of the system. That's when the fun starts. I'm looking forward to determining the State of Charge of the Batteries, monitoring the power input from the solar system and the, long overdue, equalization of the House Battery Bank.

But I'm not reaching to far to soon. I'm guessing the last part of the puzzle will not arrive until Monday - the new T-Mobile Sim Card. 

Ok, working on the list tomorrow - Friday then I'm taking a day off on Saturday - actually going sailing on my buddy's Catamaran - Lady Gray.

See you on the water.






Wednesday, June 15, 2022

Victron System Install - First few days.

Victron System Install


Before we start work on the Old  Power Management System removal in order to install the new Victron Power Management System, we have to make the boat safe.

Day 1 was to prep the boat so that the bilge pump would still have power but the rest of the system would not.   That was pretty straight forward. The bilge pump system is wired directly to the +ve of the house batteries. So disconnecting the main battery cable does not disconnect the bilge pump.

The rest of day one was planned to be for removing all of the old equipment that is associated to the Freedom 20 inverter/charger and the DC Management system.  That went well, and I was able to pull all of the old electrical part of the system by the end of the day.

It's nearly Summer here in South Florida, so it's only reasonable to work on the boat without Air conditioning for a few hours, I managed 4 hours for day 1.


Day 2 was for removing the wiring. Just as well, I found a bunch of wires that were not suitable for reusing despite that being the plan. My rule of 'If it doesn't look right then rip it out' came to the front and I removed all of the system interconnect wires as well as the 110v system wires that were too short to fit the location of the new Victron Multiplus 3000 Inverter Charger.  So that completed day 2. But I finished getting that done and still had some energy left to continue. So I started on the list for Day 3 which involved installing the physical components of the new system. I was able to install the new Victron Smart Shunt.

Day 3 and I continued with the installation of the equipment. That included the Initial fit of the Multiplus. The install of the GX Touch display/control panel was a bit more involved, I had to make a new mounting panel as the hole in the old one where the Heart Link 2000R control panel was installed was too big to allow the new GX touch to fit.  I went to Lowes and they cut a piece of plywood that was an almost perfect fit for the size, all I needed to do was drill a few holes in it, sand it smooth and apply a couple of coats of Varnish.

Day 4, time to continue installing the replacement wiring. This was the most challenging part. Luckily, Peggy came down to the boat with me and helped pull the new 110v Shore power cable from the dreaded Cockpit port side locker, through the bulkhead and into the bathroom. Then it passes through the bathroom cabinet, through another bulkhead and into the enclosed shelving above the Nav Table.

I decided to route the new cables using a shorter route than the originals. That involved drilling a hole in the liner below the Nav Table, that was easy, and then another hole in the shelf behind the electrical control panel. This is a much better route for those cables and it provides a neat route for some of the other cables.

Day 5, but now I'm behind schedule, nothing to worry about, but getting it done right is better than getting done quick.  It was Wednesday, and the outside temperature is in the mid 90º's That Fahrenheit. 
So I cut back on my time on the boat and updated the plans. But really good progress today. The Multiplus is installed and has the DC as well as the 110v wiring connected. The Cerbo GX is installed and wired except for the power connection, same with the 4G LTE Modem.

Ok, waiting for a few more items for the project. Switches, LED Lights, Sim Card. They are due Friday.

So right now I'm pretty happy with the progress. I do have to get some #10 AWG Red Tinned Copper stranded wire for the Start Battery to Multiplus Trickle Charge connection and #1/.0 AWG Green wire for the Earthing stud connection to the Engine's Ground connection bus bar.

I'm actually going sailing on my buddy's boat on Saturday, hopefully I'll get a lot more done before then.

So it's about a week before we might get this all done. Just as well that I enjoy this stuff.

See you on the Water.

Saturday, June 4, 2022

Memorial Day Cruise 2022

Memorial Day Cruise - the good, bad and ugly

The Plan: Sail down to Billy's Point in Biscayne Bay and meet up with some of the HISC Club member's boats over the Memorial Day Weekend returning on Monday/Tuesday. And have fun doing it.

 We had loaded the boat with bedding, food, fuel, water, wine, Rum and Whiskey. We were ready for this trip and the forecast was looking good, any bad weather was expected to stay North of Port St. Lucie.  

We started the day early, up at 5am, breakfast of Cereal & Toast, by 7am, we had the diesel engine running and prepared all of the lines to leave the dock. The morning weather report was for very little wind from the South, so going outside on the Ocean would have been a day of motoring with little to no wind. It was looking better to head down to Miami on the ICW. 

In preparation for the trip with the option to go down the ditch, I had printed out a list of all the ICW bridges between Port Everglades and the Port of Miami.  The list included the bridge names, distance from the previous bridge and it's opening times. The list was at the ready at the helm. So the decision was made to go down on the inside ( sailors down here refer to the ICW as the ditch, or 'the inside' rather than the Ocean route )

The New River bridges close down for the morning rush hour from 7:30am until 9am, so our plan was to leave the dock around 6:15am which would mean that we would get out of the canal within two hours of high tide.

We heard Chris and Kelli on Summer wind call for the Hillsboro Inlet Bridge opening, seems they were going on the outside, we were already down south of Port Everglades, it would be interesting to see how our progress towards Biscayne Bay differed. Later we heard Summer wind call for the Dania Beach Bridge to open, so we figured they had decided to come inside at Port Everglades and continue down the inside. Summer wind is a Catalina 36 and has a larger engine than Eximius, so I expected them to catch up with us by the time we got to Biscayne Bay.

All of the bridges opened as expected except for the Venetian Isle (West) bridge. Our GPS showed our arrival time at the bridge to be at 12:02 which would typically be as it completed it's opining. I called the bridge tender requesting the bridge opening. ( they are not required to open on a scheduled opening time if no vessel has requested it ). At 11:58am, we could see that the bridge was already open. Bridges rarely open early - normally that would be because of a commercial tow or tug or it could be an emergency vessel. In this case it was a Miami Fire Boat, I'm sure nobody would have any issues with the bridge opening early, but I had issues with the fact that the bridge tender closed the bridge before 12:00, noon, instead of remaining open to allow us to pass. We arrived, as expected at 12:02 and the bridge would normally be open fully ( the Bridge tenders routinely remind vessels to stay outside of the 'fenders' until the bridge is fully open.)

So we lost a half hour doing doughnuts on the North side of the bridge, not an easy task as the number of small vessels in the area. That was the third bridge that we missed the opening, due to waterway traffic or just being unable to make the next bridge opening.


Once past Venetian, it was plain motoring past Miami down to the Rickenbacker Causeway bridge. 


We did get a good view of the The Centinela del Río, (The River Sentry) by Cuban Manuel Carbonell

Just before the bridge, over to the East is the Miami Marina Stadium anchorage. We could see it was quite busy and more boats were heading East towards it. Just in case Affection was still there as they planned, we called them on #68, #16 and #9 but no reply, so we guessed they were already on their way to Billy's Point. We could hear Summer Wind catching up to us when they called the bridges which we had already passed. 


Once past the River Sentry, we followed the ICW channel down towards Rickenbacker Causeway bridge

Just before the Rickenbacker bridge, over to the East is the Miami Marina Stadium anchorage. We could see it was quite busy and more boats were heading East towards it. Just in case Affection was still there as they planned, we called them on #68, #16 and #9 but no reply, so we guessed they were already on their way to Billy's Point. We could hear Summer Wind catching up to us when they called the bridges which we had already passed. 

Passing the bridge, we engaged the Auto Pilot once past the bridge and shortly after that Affection showed up astern of us. Able to maintain a higher speed, Jeff & Judy sped off towards the Featherbed channel. We played dodgeball with oncoming vessels, which required us to disengage Otto ( our nickname for the Autopilot) and then reengage it once the power boats passed us. 

We had passed through the Featherbeds by the time Summer Wind was visible astern North of the beds. She was sailing to the South East trying to spend some of the trip under sail. Meanwhile we continued motoring with the wind on the nose headed to Billy's Point.

Affection had anchored and we prepared to raft up on their Starboard side, Fenders out, Lines at the read and we approached them with the plan to drop our anchor to the south west of Affection's and drop back to come alongside her. That pretty well went as planned. It took a couple of tries, it's difficult to gauge small distances and we were trying to drop our anchor 90' in front of Affection. But we came alongside without a bump, lines passed over, more fenders hung by Jeff & Judy and before long we were secure alongside. Time for a Shower (hot water curtesy of 12 hours under motor) and a Rum.

Chris and Kelli on Summer Wind arrived and anchored off to the South West expecting that Lady Gray will be close to them the next day.  Chris had an issue with his dinghy and spent a while getting that fixed.

Later, early evening, Jeff &Judy came over to share some Cheese & Wine aboard Eximius and so the Socialization began.  It's always a big part of the club cruises and always a pleasure to share personal stories.

Friday night was a pleasant period, cool enough to have the hatches open but only if they had screens to keep  out the mosquitoes. Jeff complained about them on Saturday morning which was surprising as I'm normally the mosy bait. 

Saturday morning we launched 'Special T' our new Dinghy, that was a game! Jeff came over to Eximius and helped up maneuver it over the lifelines. Lesson learned - It's easier to push the boat rather then pull it when launching. I had made up a 20' long 4 to 1 Utility Hoist which we connected to the Spinnaker Halyard. The top block was hoisted to about 16' above the deck, the lower block was attached to the Bow Ring on the Dinghy. It was easy hoisting the dink, but awkward getting it over the side, Jeff helped with that and the Dink was in the water in just a few minutes.

The next challenge was  to lower the engine off the mount on our Port stern quarter, the challenge was to get the dink between the two boats rafted together. But again, we got it done and before lunch, Special T was in the water with her engine and I was able to take it for a spin. Special T is no longer a virgin! By the time we were all done, Lady Gray was at anchor off to the North East about 200yds from Affection flying here beautiful flags, they flew straight from the mast as the wind had picked up.

The plan was for the Cruise BYOG (Bring your own grub and something to share) aboard Affection that evening. Judy did us proud! We had eight people at the party and food enough for another eight. Of course the social ranked high among our cruising history. We all wore colored glow in the dark necklaces. Discussions covered everything from the trip down to the Bay, how the boats performed and the weather. We solved several of the world's problems. Jeff & Judy brought 'Tam Tams' a chocolate cookie that few of us had ever heard of. (( Barry was due to work the following week and reported back that he had found Tam Tams in South Africa, while Chris reported that they were available on Amazon

There were a lot more stories that evening, but they are best left for the original story teller to share.

Saturday night was not so comfortable.


The boat off our Port side Stern is Summer Wind - I know, Ironic. 

So sleep on Saturday night was troubled to say the least, I was up after midnight looking to see what the noise was. Jeff was up doing the same thing and he eased our stern line to allow the boats to sterns of the two boat to be set further apart. Back to sleep for a couple of hours and then dawn came through.

There was an informal plan to share breakfast on Lady Grey. We confirmed with them. the old fashioned way 'Just holler from one boat to another'. With food ready to go, we all arrived on Lady Gray where Barry & Jamie were preparing a breakfast spread. Before breaking our fast, Barry played the Star Spangled Banner - by Madison Rising. We all stood in respect of Memorial day and all of those that have given sacrifice to the freedoms we have today. 

After breakfast, with the Sun out, power boats were arriving at Elliott key and Billy's point (which was about a mile from our location) Jeff & I snorkeled out to where we expected our anchors to be dug into the sea bed. We were able to find Jeff's but Eximius' was dug in so well that we could not see it. Jeff did give me some pointers on how to snorkel effectively, so I learned a new technique that did make snorkeling much more pleasant. During the snorkel, I had let go of a large plastic noodle and, once back at the boat, Peggy and Judy pointed out that the noodle was moving rapidly towards the horizon astern of us. 
Chris was at our stern and quickly motored away in the direction of the noodle. By that time an arriving boat had spied the noodle and picked it up from the water. Chris was able to catch up with them and retrieve the noodle. Thanks Chris.

Of course, overnight, our two rafted boats swung at least 360º which created a bit of Macrame on our anchor chains.  We spent a while discussing how to unwind the chains. First option was to try and use Affection's dinghy to to swing around the anchors in the opposite direction from the storms effect and thus release the knot in the chains. That just didn't work, despite our best effort. Next we tried to untie the knot by using Affection's engines to swing the boats around, again, didn't work. Finally we decided with myself  and Chris aboard his dinghy, to pull up the chains and then Eximius' anchor allowing us to untangle the chains. That worked, but only because of a heroic effort by Chris. The water was only about nine feet deep and Chris dove several times to free our anchor but it worked.  I feel that I owe Chris at least a Noodle.

With the anchors separated, we made the decision to just leave Affection's anchor holding both boats overnight. That worked for us as we planned to haul anchor before 8am Monday (Memorial Day), so now we could leave the raft up a lot easier.  

The wind was to high for us to raise the dink on Sunday evening. Just after dawn on Monday, it had reduced sufficiently that we tried, successfully to hoist it out of the water. I had made a modification to the dink's painter ( a rope that is attached to the dingy to help control it when it's moving it around from outside the boat), the change involved putting a loop in the painter such that I could reach the loop from the deck of Eximius. That allowed the connection of the lower end of the utility hoist to the loop without having to reach below the water to attach the hoist to the bow eye of the dinghy.

With the hoist attached to the dink, we were able to easily hoist Special T up on deck, as soon as it cleared the lifelines, it swung in front of the mast and we could lower it down onto the foredeck. It went surprising well with very little effort. Special T - a Zar 9HDL dinghy weighs about 160lbs and the 4 to 1 ratio of the utility hoist meant we were pulling down on the hoist line with about a 40lb force, easily done when pulling in a downwards direction from the top block on the hoist.  So we quickly secured the dinghy on deck and went below for breakfast.

Around 7am we had Eximius' engine running and the boat set for departing the raft up. Jeff appeared on the deck of Affection and quickly assisted in us casting off from his boat, we motored astern to clear the sides and then Veer around to the North West and head for our planned route up the ICW channel of Biscayne Bay towards the Featherbeds channel. We saw that Summer wind had left a while before us and was at least an hour ahead of us.  We set the autopilot to follow the route back to the North end of Biscayne bay with the plan of deciding if we were going to go outside via Stiltsville or continue North on the ICW and head home via the ditch.

Peggy was not for us going outside. We had just gone through some heavy rain and could see the clouds dissipating on Radar, Summer Wind was already out on the Ocean and reported there was a slight swell and light winds about 45º off the Stbd bow, so it should be a nice comfortable ride home. In addition to being able to sail home, there was the advantage that we would not have to deal with all of the bridges between Miami and Port Everglades. For me the choice was obvious. The weather had improved and the Bay was nice and flat, we were sailing with just the Genoa out doing about 4 to 5 knots on under 1900 rpm of the engine, and with the wind 45º off the bow outside, it really should be a faster ride if we put out the Main sail as well. So I was for going outside. Peggy was not, quite adamantly so. Captain made the decision, we turned towards the channel entrance at Stiltsville.    -- MISTAKE --

As we motored along the Stiltsville channel, following many other boats, both sailboats and power boats, the sea was very calm but I had furled in the Genoa and we had a very gentle journey to the Ocean, it was quite relaxing.

Once outside of the Channel, we started our slow turn North, my plan was to ride the gulf stream and reduce our trip time back to Port Everglades. We headed about 33ºM keeping an eye on our ground speed, looking for a knot or two lift to the North when we reach the gulf stream. That happened around Noon so at that time I turned North, we were outside of the route to Miami channel and so I put in the Port Everglades Outer buoy as the target destination. Skies were clear, not much wind but I put out the Genoa and we kept the diesel running, still below 2000rpm. 

Well, that didn't last! We were about 7 nautical miles south of Port Everglades, wind started to pickup and I furled in the Genoa to just a handkerchief. We were motor sailing with the wind backing more to the North, Seas were starting to pickup. Peggy was not happy, that's putting it lightly. We normally wear our life jackets when on the Ocean, but at this point we put on our Tethers and, with Peggy below, I hooked my tether near the helm. The wind increased. Sorry, but our wind data was not working ( more on that in the next post), however, we received a VHF call from Summer Wind advising that the winds near the Port Everglades Entrance were sustained at 20knots and we knew it was gusting, but we were doing 6 - 7 knots through the water but only 4-5 knots overground despite the Northerly winds. I furled in the sail completely.

All of sudden, while dealing with the significant wave action and the gusting winds, our speed through the water dropped to 2knots! We're less than two miles off shore, waves wanted us to go that way and the wind was not steady North but gusts seemed to veer to the East. 

I guessed we had picked up something on the Prop and instead of it pushing water astern of us thus moving us forwards, it's now probably just a ball spin with virtually no propulsion. I also noted that there was smoke or steam coming out of the exhaust. I slowed the engine to Idle speed, shifted to Neutral, then into reverse and revved up with the intent of dislodging anything on the prop. We've picked up Poly bags before, same feeling, same process so it might work this time too. But when I put the engine in reverse, Peggy could head a 'whomping' sound from inside the cabin and the engine shut down. Again, this not a good situation. I checked the raw water strainer first, it was not totally clogged with Sargassum but close. Cleaned that out. Then I checked the Raw Water thru hull, just a few seconds to release the hose clamps with the handy tool that I keep near to that thru hull, water squirted in and so that was clear. Time to try and restart the engine before I considered calling for a Tow Boat. When I tried to start, it didn't! Ok, maybe there's a problem with the start battery - I asked Peggy to switch the battery selector to 'Two' tried to start again, nothing! Grrrr. Ok one more time, switch the selector back to normal and let's try - DUH! - the engine was still in gear! I put it into neutral, tried to start it again and it instantly started without any issues. We're moving again! 

Worried that the steam/smoke was another indication of a problem with the engine colling system, I keep the rpm below 1800 and we continued the bumpy ride up to Port Everglades. 

We both agreed that we could anchor in Sunrise Bay for the Monday night and catch the High Tide Tuesday morning , so we anchored in the Bay.

Before we took a break, I pulled the engine covers off and started checking the engine. Coolant levels - OK, Raw Water impeller pump, OK, Oil OK, Drive belt OK, we're looking good.  Clean up and take that well earned break.

We heard from Summer wind and Lady Gray that they had got back to their docks safely, things were looking better.

After a hot shower, we had Shepherds pie for dinner along with wine for Peggy, and a glass of rum on an Ice Ball for me.

We both slept well!

Tuesday morning we caught the 8:30am Sunrise Bridge opening, then the Las Olas Blvd bridge and turned up the New River. 

The New River bridges are locked down from 7:30am to 9am and 4pm to 6:30pm weekdays for the rush hour traffic. Our arrival at 3rd Avenue bridge was timed so that we would get there just after 9am. Of course, it's never that easy, the FEC Railroad bridge went down before we got past the 'Tunnel' ( that the tunnel that allows US 1 to pass under the New River. ). I decided to stay downstream of 3rd avenue bridge rather than risk getting stuck between 3rd and Andrews Avenue bridges, the wind and current would not make that an easy place to hold station. On the other hand we were near the Tunnel, the River is quite wide there, and much easier to hold station. The bridge was down for about 20 -25 minutes. As soon as it was rising, we turned upstream and called 3rd avenue bridge for an opening. As we passed under 3rd, we could see there was a 70' motor vessel under tow between the two bridges. Good decision not to pass 3rd any earlier.

Once past 3rd avenue bridge, Andrews Ave bridge opened, the downstream heading vessels held back while the upstream vessels, and the Tow, cleared, then we turned and followed the Two through 7th avenue bridge, we then turned onto the North fork of the New River and headed back to our dock.

As always, it was a memorable trip. Thanks Jeff, Judy, Chris & Kellie, Barry & Jamie, we really enjoyed the trip, even the challenges. Looking forward to next year.

Of course, I would be totally remiss if I didn't acknowledge Peggy's better choice for the trip home. 

Humble Pie








Monday, May 23, 2022

Palm Beach Sailing Club Regatta 2022

Hillsboro Inlet to Lake Worth - Regatta 2022

This was our third participation in the Palm Beach Regatta. Our first earned us a Trophy for the best story as none of the boats in our class finished due to a nasty squall 30 minutes from the finish and we had the best story. Our second earned us a win in our class, our first ever win, we won against a Catalina 36 so we did really well despite not being a racing boat ( if you saw how much 'stuff' we carry for cruising, you'd probably agree  -  not a racer) and then, there was the 2022 regatta.

The Regatta has a 'Skippers' meeting on the Friday before the actual race. The meeting was held at a Condo's Dockside venue where most of the crews turned up to learn about the race details. Nothing new. The anticipated reduction in the span at at the Hillsboro Inlet Bridge had not taken place yet so the bridge work was not an issue. The weather was expected to be steady for the entire race day with the wind shifting from the SW to the NW later in the day. But, hey! we've never had 'great' weather in our past participation in this race.

At the end of the skippers meeting, Loony Poons ferried the crews back to their boats on Lake Boca, it was a pretty peaceful night, well except for one crew, no names = no pack drill, that kept their conversations going into the early hours of the next day.

We picked up our crew, Ira, and headed down the Intra Coastal to Hillsboro Inlet Bridge then out of the inlet and North to the starting line. Our class was second to start. Warning at 10am, start at 10.05. I screwed up the start, seriously! Far to far offshore and we missed the start by 20 minutes, but Hey! We're not racers, so not a big deal. However the race Committee boat, Lady Grey, was also in the race, so they left the line, headed south and turned to get back to the start line for their start, that was a few minutes after we crossed the line. I did verify with the Beach Committee that we had actually crossed the start line.

We headed off on a North Easterly course hoping to get into the Gulf Stream and grab a ride up North. We turned onto a Northerly course.  The Spinnaker boats mostly stayed closer to the shore except for Lady Grey which quickly passed us on our Stbd Side. We soon felt the push of the Gulf Stream and our Nav system reported that we had a couple of knots Northerly drift which confirmed it. The Nav system reported that we should be at the finish line by 16:00 WooHoo! We'll actually  finish this race.... if all goes well .

By about 1300 we had made good progress, the reefs had been shaken out and we were looking at a 15:00 arrival at the finish line. A big black foreboding cloud system appeared on our Port Quarter. We could see it on the Radar and it looked as though we would pass ahead of it, so we sailored on. Of course, we didn't 'pass ahead of it' and it picked up in wind speed quickly, no time to reef, just hold on and keep the boat from tacking or gybing. Peggy was done, she went below, it was too much for her  - Sorry Honey! Ira and I kept control of the boat and the squall passed after about 15minutes. At one point we were doing 10.2 knots over the ground thank to the push of the Gulf Stream. Here's a link to the track on our Inreach, follow it around Noon. Our speed reduced to less than 3 knots during the height of the squall which is no surprise as my goal was to keep the boat off the wind on a Port Tack, I didn't even consider trying to Heave too, the wind was changing direction so much.

Back on course after that squall, Peggy still below and Ira not really complaining, we both joked about it, just a bit. We saw a second squall playing tag with us. This time we reefed, One reef in the Main and one in the Headsail. The second squall was much more easily managed and only lasted a few minutes.
I briefly considered starting the engine but dismissed that thought quickly.  Two reasons, one it would have taken us out of the race and the boat was really holding well despite the weather. And two, I was not sure if  myself and Ira would be able to change the sail configuration even with the engine running. As I said, we've had squalls hit us before and much worse than these two, the boat has stood up to them without any issues. Yes it will dip a rail below the waterline but won't stay that far over too long. Our worst storm to date has been with 52knot winds. It's a strong boat.

With the storms past, even the Radar showing a clear sky to the West and North, we started out turn towards the Lake Worth Inlet and were doing a pretty good speed, we could finish well before 16:00 despite loosing time due to the storms. Of course, the wind veered (rotated clockwise) towards the North West and that meant we could not make the Finish mark on our current tack despite heading up to wind whenever the chance arose. By this time, Peggy was felling much better and had opened the Cabin Hatch to peek out, all was well. But we could not make the mark on our existing Port Tack. Eventually I gave up trying and headed North to the Mark on the other side of the inlet and then tacked to the West towards the finish mark and we easily made it, passing less than 100 feet from the mark.

We actually finished the Race at 14:42 and it took us a few seconds to capture a pic of the GPS Chart plotter showing our position. Peggy took a pic of the #3 Green Buoy.

Once past the finish line, we turned on the engine and into the Inlet lowing the sails when chance arose. The boat was nice and tidy topsides before we got to the next buoy. That was not the case for down below. Despite our thinking that we had secured for sea, the cabin deck was awash with books, cushions, charts, and the contents of one locker that had not stayed shut. Nothing broken and it only took a few minutes to clear it all away.

We headed to the ICW and South to the Palm Beach Sailing club, and then turned East into the mooring field looking for a place to anchor. With Peggy & Ira at the wheel and myself on the bow, finding a suitable spot as we passed Jim Wallace aboard Contrails, we turned the boat and anchored, digging in hard in anticipation of strong winds later that night/early next morning.

Peggy & I in the cockpit gave Ira first dibs at taking a shower with hot water after running the engine for 25 minutes as we motored to the anchorage.

Brent from the Palm Beach Sailing club was motoring around in one of the club's dinghies and we spoke briefly and arranged for a pickup in about 30 minutes. By that time we were ready to go ashore for the After Race Party and the Awards. Ira's wife had driven up to join us (and take Ira back home that evening). We had a great time at the party, it was super noisy, but everyone seemed to be enjoying it. They had a big screen showing the Derby horse race, the outsider 80-1 won the race, but I think we had the better race.


This was the only photo of the night for us. 
Ira & myself accepting the award for coming 1st in the Gunkhole Class
(OK, we were the only boat in our class - but we finished!)




It was a great race, will definitely do it again next year, I'll ask Ira too!



Friday, April 15, 2022

The Hunt for a new Dinghy

Our hunt for a new Dingy

Our 7'11" Mercury Dinghy has passed it's expiration date, it's intent on letting go of it's preferred position atop of the water, it's time, it's overdue. Time to give up and let it go. Sad, but it's pretty insistent. First the slow air leak from all of the (3) tubes, a couple of seams began to let go and the latest, the sadest, is the sloshing sound of water inside the boat.

There are a few fundamentals when it comes to owning a boat:-
  • Keep the water out
  • Keep the Keel down and the Mast up
  • Keep some method of propulsion
  • Keep on smiling - you've got a boat!
That first one, 'Keep the water out' is #1 for a reason and if you have ever seen a sadder sight than a sailboat's mast sticking up out of the water then you'll get it. Keep the Water Out and our dinghy is not doing that anymore.

According to the Google University, our Hypalon Dinghy should have a life of between 7 and 15 years. We've had ours since 2011, it's 11 years old. We could get it repaired, probably cost between $500 and $1000 to fix depending on how many air leaks the pros find while fixing the water leak.

The current Mercury 240 Hypalon Dinghy is now off the boat, I have started to recover a few things from it that might be of use to us or to someone else.

Besides the old Hypalon fabric that is not worth a dime ( but if you're quick you can have it, reach out to me to see if it's in the garbage yet.)

I was able to save a few things:- 
  • The fittings that our dinghy nav lights attach. They are really good and will get fixed to the new dinghy when we get one.
  • The Fiberglass Seat. Can't see a use for it. Want it? reach out to me.
  • A Sunbrella cover I made for the underside of the dinghy. We keep the dinghy on our foredeck and the Sunbrella cover minimizes the UV exposure of the dink. It probably won't fit a new dinghy, I made it custom fit for the old Mercury Dink. The Sunbrella cover is in great shape, but it will not fit whatever dinghy we purchase, so anyone want, $25, pick up sounds like a good deal for someone.

OK, now the search for a new dinghy. It's not the best time to buy as inflation is crazy right now, especially if it's anything to do with boars.

Most suppliers are just out of stock for 10' or shorter dinghies.  Most websites are showing not available till 2023. Most of the distributors I have called don't even reply, not by phone or by email and that's mostly Florida companies. One company did reply, Inflatable Boat Pros in Pompano Beach, I'm going to visit them when they have completed their move in a few weeks time. They actually have a few boats in stock, we'll see.

Ok, that's the plan. Wish me luck. Oh! If you want that seat for the Mercury Dinghy or the Sunbrella Cover, reach out to me (leave a comment with your contact info)

Paul


Friday, April 8, 2022

Our Battery Charger Failed - Part III

 Our Battery Charger Failed - Part III

We have all of the Bits!

The last part of our system's new equipment arrived at e-marine in Fort Lauderdale and we picked it up today.


Say hello to our new Victron GX Touch 50 Display Unit.

It connects to the Cerbo GX HDMI output and the Cerbo GX USB outlet.

It can be surface mounted with or without the black frame.

That cute little black thingy is the Release tool required to remove the Display panel from the Frame.

Better not lose that thingy.





With all of the equipment, it's time to start on the project. I'm going to proceed with the plan working on the boat one day and working to pay for it all the next. So it should be done in 20 days.

Next available day is Monday, April 11th 2022.

Peggy is up to taking videos of the project, I'll still keep the blog articles going, covering each step as outlined in the Plan, but Peggy is going to see how much we can capture on video. Should be fun.

If you have any questions about my choices of equipment, the removal of the old and the installation, setup and testing of the new, please post them in the comments. 

Oh, late update.
It occurred to me that we may not see the back of the GX Touch 50 for quite a while.

So, here it is.

Those 4 threaded screw holes in the back are for mounting if not using the mounting plate. The device came with 4 threaded rods with wing nuts.
Alternatively, the frame can be screwed to the surface and the display clips into the frame. (That's what we will be doing) 



Monday, April 4, 2022

Our Battery Charger Failed - Part II

 Part II of replacing our Power Management System


Part 1 described the situation: Our Zantrex Inverter Charger failed and would not charge our batteries. 

This part is going to cover the removal of the existing system, installation of the new system and any 'gotchas' during the process. I expect that this upgrade should take about 6 days. My plan is to keep the boat as safe as possible during the process, keep my sanity in check and try to not allow too much project creep. ie. avoid adding additional projects.

In preparation for this task I have spent months studying the boat electrical system, the standards used to today and the theory behind the methods and practices. I spent a Day at a Victron Tour learning about the equipment and gained some good ideas about how to get the most out of the system. I found an online course that allowed me to update my electrical knowledge converting it from my training in the Royal Navy working on Military Helicopter systems. So I feel quite confident about doing the work, however, I also decided to purchase the equipment from a Victron dealer locally that has a good reputation as reported from several of the Sailors in our local sailing Club - The Hillsboro Inlet Sailing Club.

Long term I anticipate upgrading our Solar System, this upgrade will facilitate that. If I decide to upgrade the batteries to LifePo4 or some other new battery chemistry, this upgrade will allow that.

Timing of the upgrade is also important: We like to use our boat! We have already taken Eximius out on three separate cruises this year: New Year's Eve Cruise, Change of Command cruise and St. Patrick's Day cruise. We are planning on taking the boat out for the Spring Fling on April 15th and a weeklong cruise down to Biscayne Bay for the Memorial Day Cruise. Of course, if we get the chance well get the boat out when the chance allows. But the first goal is to get the work done before April 15th. So we'll have between the March 21st and April 15th to get everything done.

Ok, time to get things together. The Victron Dealer in Fort Lauderdale is e-marine just off of State Road 84, west of I95. They advised me that the equipment should arrive by midweek March 13th- March 18th. If so, then we should have all of the equipment before we head off to the St. Pat's weekend Cruise.

March 28th. 

e-Marine had nearly all of our gear, We drove down to State Road 84 where their office is located to review my wiring diagram and pickup the equipment. The only thing we're missing is the GX Touch 50 display / control unit. That should arrive in the next couple of weeks, apparently a Thousand of them are arriving in Atlanta next week (1st week of April)

This Bad Boy was the biggest unit and would not fit in the bag, just as well, the bag would have failed, the Victron Multiplus 3000 120v 120A is a beast! I'll have to be careful when we carry that onto the boat.

I took pictures of each unit, with the cables.



Unless the Multiplus is considered, the devices and cables don't look like $2,400, but the magic inside the devices and the Multiplus do.

The GX Touch 50 is missing as mentioned, it should arrive around April 15th and it has it's own cables.

I have yet to figure out how to connect my Laptop or Tablet to the system, that will have to wait till it's all installed. It will either be via the WiFi network of the Cerbo GX, a wired connection (USB ?) or Cat5 cable however, my laptop does not have a Cat5 connection. We'll have fun figuring how that works.  I'll ask they guys on the FB Victron forum.

While waiting for the equipment to arrive, I had another thought about the schematic. I have decided to move the Dual breaker for the 110v AC so that it is between the Shore Power Connection and the Victron. On the old Freedom 20, the breaker is between the Freedom and the 110v distribution panel. 
On the one hand I want to have the disconnect before the Multiplus, on the other, I like having the option to turn off all of the 110v devices with a single switch (which is what we have right now.

The Reverse polarity indicator needs to be on the Main Disconnect switch.  So rewiring the current disconnect switch so that it breaks the input to the Multiplus would also provide the reverse polarity test prior to the Multiplus and it will be ok to just individually break the supply to the various 110v devices (Hot Water Heater, Air Conditioning, Outlets).

Ok, just fixed the wiring diagram, looks very doable. I have checked that we have all of the inter connections. As mentioned previously, I may have to replace some of the heavy duty cables from the Multiplus and the Bus bars, maybe the 110v cables from the shore power connection to the Main Shore Power Disconnect.



The updated diagram shows the new connections for the Main Shore Power Disconnect along with the 110v available LED and 110v Reverse polarity and Lamp test switch. It also shows the connections for the Shunt Power -ve and the Aux connection to the Start Battery - this should result in being able to monitor the Voltage of the Start Battery.  Just an FYI the 110v Neutral and Earth Terminal blocks are the Neutral and Earth connections for each of the 110v devices.

We'll see.



Back to the timetable.
We've planned on going on a Memorial Day Cruise on our boat, so it either has to be finished a few days before that and I figure it will take about 10 days, allowing some wiggle room. So we have to have started by May 18th or wait till after June 2nd.

We're also doing the Palm Beach Sailing Club Regatta on May 6th - May 9th. Which means we have to finished the install by May 3rd, which means we would need to start by April 22nd or wait till after the Regatta.
So, choices are:
Start by April 22nd else wait till after May 9th.

Start by May 18th else wait till after June 2nd.

Today is April 4th. which gives us 17 days to our first Waypoint. 

Of course, I have a bunch of commitments for the next couple of weeks. So I had better get busy.

A sailor with a plan - and a couple of backups. We' re good.

More soon.